It is difficult to compare solid wood flooring to engineered wood flooring due to the wide range of quality in both product categories, particularly engineered. Solid wood has some limitations. Recommended maximum widths and lengths are typically 5" / 127mm wide and 7' / 2100mm long. Solid hardwood is also more prone to "gapping" (excessive space between planks), "crowning" (convex curving upwards when humidity increases) and "cupping" (a concave or "dished" appearance of the plank, with the height of the plank along its longer edges being higher than the centre) with increased plank size. Solid wood cannot be used with underfloor radiant heating.[5] However extra care is necessary with the planning and installation of the heating system and the wood flooring, such as limiting the temperature to 85 °F (29 °C), avoid sharp temperature fluctuations, utilizing an outdoor thermostat to anticipate heating demands, and monitoring the moisture content for the subfloor before installation.
Solid hardwood floor planks are made from a piece of wood and made to be anywhere from 18 to 20 mm thick. The boards are made with a tongue and groove to fit together for installation. Depending on the species of wood, certain floors will be harder than others. The harder the floor, the less susceptible it is to dings and scratches. The floor can be sanded and refinished several times to restore its beauty, with the total number of times being determined by the depth of the tongue from the top of the plank. Denver Hardwood Flooring

With so many potential problems and repairs that a wood floor could need, you’re probably wondering how much the potential solutions will cost. It might make you feel better to know that the average wood floor repair costs around $1000, with minor repairs costing as little as a couple hundred and major jobs costing well in to the thousands. This is definitely a job that you’ll want to get a few quotes from contractors in order to feel comfortable with your particular repair needed or how you can repair the wood floor yourself. Hardwood Floors
Most floors use a tongue-and-groove design for connecting adjacent strips. This design makes replacing a single strip or plank challenging, but not impossible. First, look for any nails in the damaged board and drive them as far through the board as possible by using a hammer and nail set. Carpenters use nail sets to drive nails flush with trim without damaging the trim with a hammer. After you’ve cleared the nails, it’s time to remove the damaged board and install a new one. Follow these steps:
Solid hardwood floors are made of planks milled from a single piece of timber. Solid hardwood floors were originally used for structural purposes, being installed perpendicular to the wooden support beams of a building known as joists or bearers. With the increased use of concrete as a subfloor in some parts of the world, engineered wood flooring has gained some popularity. However, solid wood floors are still common and popular. Solid wood floors have a thicker wear surface and can be sanded and finished more times than an engineered wood floor.[2] It is not uncommon for homes in New England, Eastern Canada, USA, and Europe to have the original solid wood floor still in use today. Denver Hardwood Flooring
A number of proprietary features for solid wood floors are available. Many solid woods come with grooves cut into the back of the wood that run the length of each plank, often called 'absorption strips,' that are intended to reduce cupping. Solid wood floors are mostly manufactured 0.75 inches (19 mm) thick with a tongue-and-groove for installation. Hardwood Floors
Before you choose a hardwood floor, think about how much foot traffic you expect. Consider the look you want and how much you plan to invest. And, if you’re still undecided, browse our selection of other flooring options, including vinyl flooring, tile, parquet, and laminate flooring. You can also find helpful information in our cost guide. From selection to delivery and installation, the Home Depot is your one-stop shop for all your flooring needs.
With so many potential problems and repairs that a wood floor could need, you’re probably wondering how much the potential solutions will cost. It might make you feel better to know that the average wood floor repair costs around $1000, with minor repairs costing as little as a couple hundred and major jobs costing well in to the thousands. This is definitely a job that you’ll want to get a few quotes from contractors in order to feel comfortable with your particular repair needed or how you can repair the wood floor yourself. Denver Hardwood Floors
Another common hardwood floor malady is the development of gaps between planks. The most common causes of gaps between the boards is Mother Nature. Wood shrinks as it dries out, and it expands when it gets wet and humid. That regular expansion and contraction over time is the most common cause of gaps, and is the main reason why most gaps are seasonal in nature. Perhaps your best plan of action is to exercise patience.
The hardwood flooring we offer delivers unmatched beauty, durability, structural strength, and overall long life to your home or commercial space. Hardwood flooring is in a class by itself; not just a choice in flooring, but more like a tradition. We make sure that all of the hardwood floors we offer honor that tradition, and meet all of your expectations too, ensuring you receive the perfect hardwood floor for your living space.
The age of your floor also plays a role. If your floor has been in place for decades, it may resist refinishing for a number of reasons. For instance, if it has already been refinished several times or if too much of the surface wood has become exposed, refinishing your floor may have little effect. For very old floors, replacement can often be preferable to refinishing. Denver Hardwood Flooring
To fix a buckled floorboard, you need to be able to access the floor from below. The way to tackle this problem is to put weight on the buckled area from above — a cement block works well. Then install a 1 1/4-inch screw in the buckled flooring from below. Allow the screw to penetrate only halfway into the flooring, or it may come up through the finished surface. Driving the screw through the subfloor and into the flooring pulls the flooring down against the subfloor and gets rid of the buckled spot. Denver Hardwood Floors

Solid hardwood is great for high traffic areas and rooms on the first or second floors where there’s limited moisture. You can purchase your solid hardwood floors either prefinished or unfinished. Prefinished hardwood floors have a coating that protects them and they’re ready to install right out of the box. Unfinished hardwoods allow you to apply your own stain color.
Cut a new length of flooring to fit snugly into the space of the old board. It doesn't matter what kind of saw you use to repair your hardwood floors; just make sure the cuts are perfectly square. After trimming the board to length, turn it upside down and use a chisel to chop off the lower lip of the grooved edge (photo 5). That allows it to fit over the protruding tongue of the adjacent floorboard. Test-fit the new piece. If it's slightly lower than the surrounding floorboards, shim it up with strips of kraft paper. Then remove the board and spread carpenter's glue on the tongues and grooves of the new and old pieces. Slip the new board into place (photo 6), protect it with a scrap-wood block and tap it down with a hammer. Cover the board with wax paper, then hold it down overnight with heavy books or weights. An alternative to gluing: Simply face-nail the board with 6d finishing nails. Bore pilot holes at a slight angle, then drive in the nails. Tap them below the surface with a nailset (photo 7) and fill the holes with wood putty. Lightly sand the entire board smooth, but be careful not to remove too much finish from surrounding boards. After finding a matching stain color by experimenting on scraps of flooring, stain the boards to match the original floor. Let dry overnight, then apply two coats of clear polyurethane varnish. If the old floor is unstained, just apply the polyurethane. Denver Hardwood Flooring
Instead of boiling the hardwood logs, in this process they are kept at a low humidity level and dried slowly to draw moisture from the inside of the wood cells. The logs are then sawn in the same manner as for solid hardwood planks. This style of engineered hardwood has the same look as solid hardwood, and does not have any of the potential problems of "face checking" that rotary-peel and slice-peel products have, because the product is not exposed to added moisture. Denver Hardwood Floors
To fix a buckled floorboard, you need to be able to access the floor from below. The way to tackle this problem is to put weight on the buckled area from above — a cement block works well. Then install a 1 1/4-inch screw in the buckled flooring from below. Allow the screw to penetrate only halfway into the flooring, or it may come up through the finished surface. Driving the screw through the subfloor and into the flooring pulls the flooring down against the subfloor and gets rid of the buckled spot. Hardwood Floors
×