Lowe’s has what you need to bring value-adding beauty to your home with hardwood flooring. There are plenty of species to choose from, including acacia wood flooring, walnut flooring, maple flooring, hickory hardwood flooring and cherry wood flooring. Depending on your budget and room’s traffic level, you’ll be sure to find a style to suit your needs.
Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7]

Floating installation: A floating installation is where the flooring is laid down in a glueless manner on top of a layer of underlay. The individual planks are locked together, and are not glued or nailed down to the subfloor. By doing this the floor is floating above the underlay, and can be laid on top of existing tile or marble, without the risk of damaging the subflooring. Denver Hardwood Flooring


Because tongue-and-groove boards are locked in place, removal involves cutting out the middle of each damaged board. The easiest way is to bore a 1-in.-dia. hole through both ends of each damaged board (photo 1). Then use a circular saw to connect the two holes (photo 2). Follow these steps to safely make the plunge cuts you need to repair your hardwood floors: 1. Adjust the depth of cut to the thickness of the floorboards. Plug in the saw and put on eye protection. 2. Pull back the retractable blade guard with your thumb. Then hold the nose of the baseplate on the floorboard and lift up the rear of the saw. 3. Align the blade with the right edge of one of the holes. Make sure the blade isn't touching the floor, then squeeze the trigger and slowly lower the spinning blade into the board. 4. Grip the saw firmly with both hands and guide it in a straight line until you cut into the right edge of the hole at the opposite end of the board. 5. Move back to the first hole, align the blade with the left edge and cut to the left edge of the second hole. Pry out the middle section with a hammer and chisel. Chop out the remaining edges, being careful not to damage any surrounding boards (photo 3). The "tongue" piece will be nailed in place, so break it out in small pieces. Then pull out the nails with a hammer or locking pliers. The existing floorboards have a tongue and groove milled on each end and along the edges. Chop off the tongue exposed by the board you just removed so you can slip in the new board (photo 4). Denver Hardwood Floors
 116% harder than Red Oak (1)  12% harder than Red Oak (11)  123% Harder than Red Oak (4)  125% harder than Red Oak (2)  141% harder than Red Oak (2)  15% softer than Red Oak (2)  165% harder than Red Oak (2)  174% harder than Red Oak (5)  18% softer than Red Oak (1)  185% harder than Red Oak (4)  198 % harder than Red Oak (2)  2% harder than Red Oak (2)  2% Softer than Red Oak (1)  25% softer than Red Oak (1)  28% harder than Red Oak (1)  30% harder than Red Oak (8)  33% harder than Red Oak (2)  41% harder than Red Oak (7)  43% harder than Red Oak (1)  5% harder than Red Oak (8)  53% softer than Red Oak (1)  6% harder than Red Oak (14)  67% harder than Red Oak (5)  74% harder than Red Oak (2)  81% harder than Red Oak (2)  82% harder than Red Oak (2)  9% softer than Red Oak (1)  about the same as Red Oak (7)  Benchmark at 1290 on Janka Scale (37) Denver Hardwood Flooring
Floor connection system: There are a wide range of connection systems, as most of them are mill-specific manufacturing techniques. The general principle is to have grooves on all four sides of the plank with a separate, unconnected, piece that is inserted into the grooves of two planks to join them. The piece used for the connection can be made from wood, rubber, or plastic. This installation system allows for different materials (i.e. wood and metal) to be installed together if they have the same connection system. Denver Hardwood Floor Install
No matter what type of hardwood flooring you choose, proper care and maintenance will help them look beautiful even longer. First off, don’t let the dirt and dust collect. At least once a week, you’ll want to go over your hardwood floors with a broom or dust mop to pick up any dirt, dust, hair or pet dander. If you’re using a vacuum, make sure it’s set to ‘wood floors’ so that you’re not beating up your floors and damaging them in the process. Hardwood Floors
Glue down engineered hardwood, alternatively. If you don't want to nail down the boards, you do have the option of using adhesive to put engineered hardwood in place. It's a good choice, but won't last as long or be as sturdy as nailed down hardwood. The procedure is very similar to the nail-down process. Follow the adhesive manufacturer's instructions for installation and drying times.[11] Denver Hardwood Floor Install
If your floor has noticeable scratches throughout, your best option is to sand down the floor and refinish it. A complete sanding removes scratches, but beware: This only works on real wood floors, not bamboo. If you have an engineered wood floor with a real wood surface, make sure the real wood surface is more than 1mm thick—sanding usually takes at least this much wood off the surface, so a thicker layer is required for a complete sanding. Denver Hardwood Flooring
Tongue-and-groove: One side and one end of the plank have a groove, the other side and end have a tongue (protruding wood along an edge's center). The tongue and groove fit snugly together, thus joining or aligning the planks, and are not visible once joined. Tongue-and-groove flooring can be installed by glue-down (both engineered and solid), floating (mostly engineered only), or nail-down (not recommended for most engineered). Denver Hardwood Flooring
Visual – While hardwood flooring is limited by species and stains, Rigid Core flooring has near limitless options when it comes to flooring that looks like wood. In addition to traditional wood visuals and colors, you can pick from stone looks and even hybrids that marry wood and stones together into unique new options. And best of all you will benefit from a curated look that removes unwanted imperfections like oversized knots, holes, and worming that naturally occurs in hardwood floors. Denver Hardwood Floor Install
Warped hardwood floors, also known as sagging, is a serious problem for any homeowner. It is often the result of serious moisture problems, and any evidence of warped hardwood floors needs to be addressed immediately. Warped hardwood floors are rarely the result of faulty hardwood or installation, but are a symptom of larger moisture problems in the home itself that need to be taken care of. Hardwood Floors

Hardwood species used in flooring are given a hardwood hardness rating, which indicates how resistant the wood is to dents and wear. This rating is based off a test called the Janka Hardness Test, and it measures the force needed to press a steel ball into the wood sample. The highest possible score on this test is a little over 5,000, with most traditional solid wood floors scoring in the 1,000-2,000 range. The superior density of Rigid Core flooring would exceed the limitations of the Janka test, and instead a higher impact testing is needed to measure real world performance. Here is how the general hardness of plank flooring ranks:


Start by cleaning the entire area around the scratch. You will want to remove all traces of dust and grime on the floor before you begin any other steps. Pay close attention to the inside of the crack itself, which should be totally free of dirt, if possible. If you have a wax layer, use a wax remover solution to clear away the wax before you begin the repair.
To fix a buckled floorboard, you need to be able to access the floor from below. The way to tackle this problem is to put weight on the buckled area from above — a cement block works well. Then install a 1 1/4-inch screw in the buckled flooring from below. Allow the screw to penetrate only halfway into the flooring, or it may come up through the finished surface. Driving the screw through the subfloor and into the flooring pulls the flooring down against the subfloor and gets rid of the buckled spot. Hardwood Floors
×