Solid wood flooring is milled from a single piece of timber that is kiln or air dried before sawing. Depending on the desired look of the floor, the timber can be cut in three ways: flat-sawn, quarter-sawn, and rift-sawn. The timber is cut to the desired dimensions and either packed unfinished for a site-finished installation or finished at the factory. The moisture content at time of manufacturing is carefully controlled to ensure the product does not warp during transport and storage.

It is difficult to compare solid wood flooring to engineered wood flooring due to the wide range of quality in both product categories, particularly engineered. Solid wood has some limitations. Recommended maximum widths and lengths are typically 5" / 127mm wide and 7' / 2100mm long. Solid hardwood is also more prone to "gapping" (excessive space between planks), "crowning" (convex curving upwards when humidity increases) and "cupping" (a concave or "dished" appearance of the plank, with the height of the plank along its longer edges being higher than the centre) with increased plank size. Solid wood cannot be used with underfloor radiant heating.[5] However extra care is necessary with the planning and installation of the heating system and the wood flooring, such as limiting the temperature to 85 °F (29 °C), avoid sharp temperature fluctuations, utilizing an outdoor thermostat to anticipate heating demands, and monitoring the moisture content for the subfloor before installation.
Choose your replacement hardwood flooring. You don't have to replace your old floor with the exact same wood or flooring type that you just removed! You can glue your new hardwood flooring into place if you like. You can also install nail-down, floating (or locking) hardwood flooring as a replacement. The choice is up to you and what your budget allows.
Solid hardwood floors are made of planks milled from a single piece of timber. Solid hardwood floors were originally used for structural purposes, being installed perpendicular to the wooden support beams of a building known as joists or bearers. With the increased use of concrete as a subfloor in some parts of the world, engineered wood flooring has gained some popularity. However, solid wood floors are still common and popular. Solid wood floors have a thicker wear surface and can be sanded and finished more times than an engineered wood floor.[2] It is not uncommon for homes in New England, Eastern Canada, USA, and Europe to have the original solid wood floor still in use today. Denver Hardwood Flooring

Instead of boiling the hardwood logs, in this process they are kept at a low humidity level and dried slowly to draw moisture from the inside of the wood cells. The logs are then sawn in the same manner as for solid hardwood planks. This style of engineered hardwood has the same look as solid hardwood, and does not have any of the potential problems of "face checking" that rotary-peel and slice-peel products have, because the product is not exposed to added moisture. Denver Hardwood Floors
Start by cleaning the entire area around the scratch. You will want to remove all traces of dust and grime on the floor before you begin any other steps. Pay close attention to the inside of the crack itself, which should be totally free of dirt, if possible. If you have a wax layer, use a wax remover solution to clear away the wax before you begin the repair. Denver Hardwood Floors

No matter what type of hardwood flooring you choose, proper care and maintenance will help them look beautiful even longer. First off, don’t let the dirt and dust collect. At least once a week, you’ll want to go over your hardwood floors with a broom or dust mop to pick up any dirt, dust, hair or pet dander. If you’re using a vacuum, make sure it’s set to ‘wood floors’ so that you’re not beating up your floors and damaging them in the process. Hardwood Floors
Make cuts perpendicular to the direction the wood is laying. Using a circular saw, make single cuts straight across the flooring that are about 1 foot (30 cm) to 2 feet (61 cm) apart. Be sure your cuts are perpendicular to the direction of the wood. Start on 1 side of the room and work your way systematically to the other side, spacing each cut about 1 foot (30 cm) to 2 feet (61 cm) apart.[3] Denver Hardwood Flooring
Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7]
This process begins with the same treatment process that the rotary peel method uses. However, instead of being sliced in a rotary fashion, with this technique the wood is sliced from the log in much the same manner that lumber is sawn from a log – straight through. The veneers do not go through the same manufacturing process as rotary peeled veneers. Engineered hardwood produced this way tends to have fewer problems with "face checking", and also does not have the same plywood appearance in the grain.[3] However, the planks can tend to have edge splintering and cracking because the veneers have been submerged in water and then pressed flat. Denver Hardwood Floors
There are some characteristics that are common to each category: solid wood is more frequently site-finished, is always in a plank format, is generally thicker than engineered wood, and is usually installed by nailing. Engineered wood is more frequently pre-finished, has bevelled edges, is very rarely site-finished, and is installed with glue or as a floating installation. [6] Denver Hardwood Flooring
Oak has always been a popular choice for hardwood flooring. The color is visually appealing, looks inviting, and has many advantages. You’ll find the wood easier to clean, and it easily blends in with furniture and home interior designs you already have. Plus, oak is a good investment if you’re considering selling your house in the future, since the wood can last for many years.
You may be on the fence about your decision to refinish your hardwood floors because you wonder if your floors are a candidate for refinishing. The truth is, not all hardwood floors can be refinished. Although most common problems can be addressed and fixed without replacing the entire floor, there are some exceptions. Consider the following to make an informed decision. Denver Hardwood Flooring
Add style, warmth, and value to your home with beautiful hardwood floors from The Home Depot. Our hardwood floors are available in solid and engineered hardwood, and a wide variety of colors, styles and wood species. Whether you’re interested in a traditional look, like a classic oak wood floor or something more modern and contemporary, like bamboo floors or cork flooring, we have everything you need to get your flooring project done. Hardwood Floors
The Blue Ridge Hickory Morning Fog 3/4 in. The Blue Ridge Hickory Morning Fog 3/4 in. Solid Hardwood Flooring is sealed with an Alpha Alumina finish providing protection from every day wear. This product carries a 50-year finish warranty. Each plank features a micro beveled edge and micro beveled end. You can feel confident purchasing this product because ...  More + Product Details Close
Floor connection system: There are a wide range of connection systems, as most of them are mill-specific manufacturing techniques. The general principle is to have grooves on all four sides of the plank with a separate, unconnected, piece that is inserted into the grooves of two planks to join them. The piece used for the connection can be made from wood, rubber, or plastic. This installation system allows for different materials (i.e. wood and metal) to be installed together if they have the same connection system.
Awesome explanation! When I say heat pump to people, it's amazing how often their eyes glaze over...even though most of them have had refrigerators and air-conditioners their whole lives and have never asked themselves how they work. Same principle! Compressor and expansion valve (and the heat-holding capacity of a phase change; another confusing one for people). thanks for helping educate! Hardwood Floors
The age of your floor also plays a role. If your floor has been in place for decades, it may resist refinishing for a number of reasons. For instance, if it has already been refinished several times or if too much of the surface wood has become exposed, refinishing your floor may have little effect. For very old floors, replacement can often be preferable to refinishing. Denver Hardwood Flooring
You may be on the fence about your decision to refinish your hardwood floors because you wonder if your floors are a candidate for refinishing. The truth is, not all hardwood floors can be refinished. Although most common problems can be addressed and fixed without replacing the entire floor, there are some exceptions. Consider the following to make an informed decision. Denver Hardwood Flooring
We had bought and installed this beautiful product in our downstairs a few years ago. It's now time to do the upstairs and the product was the same excellent value for the price. Arrived quicker than we needed, but gives it time to acclimate to our home. We will be using the same installer and he was happy we are ordering the same product from the same company. He was VERY impressed by the quality of the product last time. I'm excited to see the completed project as I love this wood on our main floor. Hardwood Floors
One of the best things about cork floors is that they are environmentally friendly because cork is a sustainable and renewable resource. The natural beauty of the material can suite any decor. The structure of the cork allows for a natural comfort and softness to absorb shock. This is why use of cork flooring is a good application in areas where people will be on their feet for extended periods of time. Using cork floors will reduce noise from traffic or dropping items, also because of the structure of the cork material. The natural properties of the material make it healthy because it is not only resistant to insects, but it is hypo-allergenic.

As the name suggests, solid hardwood is a single, solid piece of wood. Its natural simplicity has made it a popular flooring choice for generations, but that same simplicity makes it less than ideal for modern homes. Wood is a naturally porous material, meaning it is soft, extremely prone to denting, and absorbs water like a sponge. All of these attributes are ideal for helping trees grow, but they don’t translate well to modern flooring. Floors today need to withstand heavy traffic, drops, scratches, and most importantly, spills. Denver Hardwood Floor Install
Nothing compares with the beauty of genuine hardwood floors (especially when they're maintained well). Whether engineered hardwood or solid hardwood flooring, the glow of natural wood brings comfort and beauty to any room. Wayfair carries thousands of species of natural wood flooring, including oak, hickory, maple, cherry, birch, cork, bamboo, and exotic hardwood species. If you're new to wood flooring, read our guide that has everything you need to know.

Regardless of the floor, the protective finish will play a large role in how scratch and stain resistant it is. Both hardwood and Rigid Core flooring are available with various types of protective finishes. Rigid Core flooring goes a step beyond hardwood though, and also has a transparent solid wear layer that protects against gouging and deeper scratches. Denver Hardwood Floors
Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store.
To fix a buckled floorboard, you need to be able to access the floor from below. The way to tackle this problem is to put weight on the buckled area from above — a cement block works well. Then install a 1 1/4-inch screw in the buckled flooring from below. Allow the screw to penetrate only halfway into the flooring, or it may come up through the finished surface. Driving the screw through the subfloor and into the flooring pulls the flooring down against the subfloor and gets rid of the buckled spot. Hardwood Floors
Warranty & Brand – The value of your floor extends well beyond the floor itself. The people that created, tested, produced, and support it are just as important to consider. You want to make sure you are buying a floor from a manufacturer who you can trust. What kind of testing are they doing to make sure the floor you are buying will last? How can they help you if problems do occur down the road? What does the warranty actually cover? These are important factors to consider, especially when hardwood flooring doesn’t meet Rigid Core flooring’s abilities in areas like durability, dent resistance, and waterproofing. Denver Hardwood Flooring

Menards® has everything you need to cover your floors in style! We offer a wide selection of hardwood flooring options that are fit to use in any room of your home. Some of our quality hardwood floorcoverings include engineered hardwood, which is built to last and has higher resistance to moisture levels. We also carry a variety of solid hardwood flooring to give your home traditional character and style. If you are interested in another durable flooring option for your home, we have cork flooring. In addition to strong and durable flooring, we offer everything you will need for installation and maintenance as well as hardwood moulding and trims to help you finish the job. Once the flooring installation is complete, keep them looking clean with our selection of vacuum cleaners and floor care products. Next, complete the look with area rugs, mats, and runners to enhance your home's décor and add coziness to the space. Denver Hardwood Floor Install

Check the flatness of the subfloor. Use a straight piece of lumber that is between 8 and 10 feet in length to find any areas of the subfloor that aren't level. Simply lay down the plank and look for dips beneath it or raised humps. Mark any problem spots you find. Move the plank across the floor 1 way, then turn it diagonally and go across the surface again.[6] Denver Hardwood Flooring
Make cuts perpendicular to the direction the wood is laying. Using a circular saw, make single cuts straight across the flooring that are about 1 foot (30 cm) to 2 feet (61 cm) apart. Be sure your cuts are perpendicular to the direction of the wood. Start on 1 side of the room and work your way systematically to the other side, spacing each cut about 1 foot (30 cm) to 2 feet (61 cm) apart.[3] Denver Hardwood Flooring

Awesome explanation! When I say heat pump to people, it's amazing how often their eyes glaze over...even though most of them have had refrigerators and air-conditioners their whole lives and have never asked themselves how they work. Same principle! Compressor and expansion valve (and the heat-holding capacity of a phase change; another confusing one for people). thanks for helping educate! Denver Hardwood Floors
Installing a hardwood floor yourself can save you money – if you know what you’re doing. Improper preparation and installation can lead to warping and buckling, which will ruin flooring that would otherwise remain beautiful for years to come. The most important thing you can do to ensure the structural integrity of your floor is to properly prepare for the installation process. Here are various articles to help you!
Solid wood flooring is milled from a single piece of timber that is kiln or air dried before sawing. Depending on the desired look of the floor, the timber can be cut in three ways: flat-sawn, quarter-sawn, and rift-sawn. The timber is cut to the desired dimensions and either packed unfinished for a site-finished installation or finished at the factory. The moisture content at time of manufacturing is carefully controlled to ensure the product does not warp during transport and storage.
Maple is another great choice for hardwood flooring. Many people prefer its light tan look, which blends into home interior spaces. As one of the strongest woods, maple is a top choice for high-traffic areas of a home. The wood doesn’t scuff easily, making it a good choice for homes with children or those with a lot of foot traffic across the floors. Maple requires minimal maintenance, with weekly sweeping and annual applications of wood soap to prolong the life of the floors.
Because tongue-and-groove boards are locked in place, removal involves cutting out the middle of each damaged board. The easiest way is to bore a 1-in.-dia. hole through both ends of each damaged board (photo 1). Then use a circular saw to connect the two holes (photo 2). Follow these steps to safely make the plunge cuts you need to repair your hardwood floors: 1. Adjust the depth of cut to the thickness of the floorboards. Plug in the saw and put on eye protection. 2. Pull back the retractable blade guard with your thumb. Then hold the nose of the baseplate on the floorboard and lift up the rear of the saw. 3. Align the blade with the right edge of one of the holes. Make sure the blade isn't touching the floor, then squeeze the trigger and slowly lower the spinning blade into the board. 4. Grip the saw firmly with both hands and guide it in a straight line until you cut into the right edge of the hole at the opposite end of the board. 5. Move back to the first hole, align the blade with the left edge and cut to the left edge of the second hole. Pry out the middle section with a hammer and chisel. Chop out the remaining edges, being careful not to damage any surrounding boards (photo 3). The "tongue" piece will be nailed in place, so break it out in small pieces. Then pull out the nails with a hammer or locking pliers. The existing floorboards have a tongue and groove milled on each end and along the edges. Chop off the tongue exposed by the board you just removed so you can slip in the new board (photo 4). Denver Hardwood Floors

Rigid Core flooring is a category of resilient flooring, and it has been designed from the ground up with modern homes in mind. It’s 100% waterproof, easy to install, and provides extreme scratch and indent resistance when compared to solid or engineered wood flooring. It also offers a wide range of design options because it isn’t limited to traditional wood species. Its hybrid visuals, exotic species, colors, and textures go above and beyond anything traditional wood flooring can offer. Hardwood Floors
×