You may be on the fence about your decision to refinish your hardwood floors because you wonder if your floors are a candidate for refinishing. The truth is, not all hardwood floors can be refinished. Although most common problems can be addressed and fixed without replacing the entire floor, there are some exceptions. Consider the following to make an informed decision.
Floating installation: A floating installation is where the flooring is laid down in a glueless manner on top of a layer of underlay. The individual planks are locked together, and are not glued or nailed down to the subfloor. By doing this the floor is floating above the underlay, and can be laid on top of existing tile or marble, without the risk of damaging the subflooring. Denver Hardwood Flooring
Maple is another great choice for hardwood flooring. Many people prefer its light tan look, which blends into home interior spaces. As one of the strongest woods, maple is a top choice for high-traffic areas of a home. The wood doesn’t scuff easily, making it a good choice for homes with children or those with a lot of foot traffic across the floors. Maple requires minimal maintenance, with weekly sweeping and annual applications of wood soap to prolong the life of the floors. Hardwood Floors
It is difficult to compare solid wood flooring to engineered wood flooring due to the wide range of quality in both product categories, particularly engineered. Solid wood has some limitations. Recommended maximum widths and lengths are typically 5" / 127mm wide and 7' / 2100mm long. Solid hardwood is also more prone to "gapping" (excessive space between planks), "crowning" (convex curving upwards when humidity increases) and "cupping" (a concave or "dished" appearance of the plank, with the height of the plank along its longer edges being higher than the centre) with increased plank size. Solid wood cannot be used with underfloor radiant heating.[5] However extra care is necessary with the planning and installation of the heating system and the wood flooring, such as limiting the temperature to 85 °F (29 °C), avoid sharp temperature fluctuations, utilizing an outdoor thermostat to anticipate heating demands, and monitoring the moisture content for the subfloor before installation. Denver Hardwood Flooring
If your floors are in need of a deeper cleaning, use a wood floor cleaner. Follow the instructions for diluting the cleaner in water. Clean the floors with a damp mop, going with the grain. Then, go back over the floor with a clean, damp mop to remove any excess cleaner. Finish by drying the floor completely with a dry towel. Remember, leftover standing water could damage your wood floors. Denver Hardwood Flooring
 116% harder than Red Oak (1)  12% harder than Red Oak (11)  123% Harder than Red Oak (4)  125% harder than Red Oak (2)  141% harder than Red Oak (2)  15% softer than Red Oak (2)  165% harder than Red Oak (2)  174% harder than Red Oak (5)  18% softer than Red Oak (1)  185% harder than Red Oak (4)  198 % harder than Red Oak (2)  2% harder than Red Oak (2)  2% Softer than Red Oak (1)  25% softer than Red Oak (1)  28% harder than Red Oak (1)  30% harder than Red Oak (8)  33% harder than Red Oak (2)  41% harder than Red Oak (7)  43% harder than Red Oak (1)  5% harder than Red Oak (8)  53% softer than Red Oak (1)  6% harder than Red Oak (14)  67% harder than Red Oak (5)  74% harder than Red Oak (2)  81% harder than Red Oak (2)  82% harder than Red Oak (2)  9% softer than Red Oak (1)  about the same as Red Oak (7)  Benchmark at 1290 on Janka Scale (37)
Refinish, refinish, refinish! In almost every case it is preferable to refinish rather than replace hardwood floors. Part of the appeal of hardwood is that it lasts so long. A quality hardwood floor can be sanded down and refinished at least six times, and up to ten times before you need to replace it. You can change the color, closely match and replace warped, stained, or termite ingested planks, silence squeaky boards, and fill gaps or patch knots. With all of these easy solutions, why would anyone choose to replace hardwood floors? Well, here are the cases when a complete rehaul becomes a better option. Denver Hardwood Floors
Maple is another great choice for hardwood flooring. Many people prefer its light tan look, which blends into home interior spaces. As one of the strongest woods, maple is a top choice for high-traffic areas of a home. The wood doesn’t scuff easily, making it a good choice for homes with children or those with a lot of foot traffic across the floors. Maple requires minimal maintenance, with weekly sweeping and annual applications of wood soap to prolong the life of the floors.

Choosing teak for your hardwood floors can be a smart choice. You’ll find teak is resistant to pests, as the natural oils found in the wood are undesirable to most insects, including termites. Teak is also a water-resistant wood choice, a bonus if you have young, active children or pets that come indoors soaking wet after walks in the rain. Teak bears an attractive reddish-brown color. However, if left untreated, teak can turn a silver color if exposed to UV rays of sunlight. To prevent discoloration and wear, you can treat the wood with a coating of oil to seal it so that you can enjoy beautiful teak floors for years to come. Denver Hardwood Floor Install
Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7] Denver Hardwood Floors
We had bought and installed this beautiful product in our downstairs a few years ago. It's now time to do the upstairs and the product was the same excellent value for the price. Arrived quicker than we needed, but gives it time to acclimate to our home. We will be using the same installer and he was happy we are ordering the same product from the same company. He was VERY impressed by the quality of the product last time. I'm excited to see the completed project as I love this wood on our main floor. Hardwood Floors
Refinish, refinish, refinish! In almost every case it is preferable to refinish rather than replace hardwood floors. Part of the appeal of hardwood is that it lasts so long. A quality hardwood floor can be sanded down and refinished at least six times, and up to ten times before you need to replace it. You can change the color, closely match and replace warped, stained, or termite ingested planks, silence squeaky boards, and fill gaps or patch knots. With all of these easy solutions, why would anyone choose to replace hardwood floors? Well, here are the cases when a complete rehaul becomes a better option. Denver Hardwood Floors
The natural process of things will tend to close gaps as the weather and humidity changes. As a rule, if the gap is less than the thickness of a dime, your flooring is normal and there’s nothing to worry about. If your gaps are more persistent, you might need to call in a professional to tighten up your hardwood floor so that they cease to be a problem. Denver Hardwood Floors

Engineered wood flooring was created to lower the cost of wood flooring and attempt to fix some of solid wood’s shortcomings. It’s constructed from inexpensive plywood or particle board and topped with a thin veneer of hardwood. This construction helps with installation flexibility and slightly improves indent performance, but it adds a new set of problems as well. Because the “real” wood part of the floor is just a thin veneer, damage from scratches can be irreparable. Engineered wood floors are still made from porous wood, meaning they can’t be subjected to water. Denver Hardwood Floors
Laminate is a cost effective option that will withstand a certain amount of wear. For an easy installation, opt for click-lock. The planks will snap together and can be laid over other flooring. It is ideal for living areas, and some brands may even construct it with a waterproof core, allowing it to be used in areas where water may be an issue. We suggest taking a close look at the guarantee before installing it in a bathroom. Denver Hardwood Floors
Awesome explanation! When I say heat pump to people, it's amazing how often their eyes glaze over...even though most of them have had refrigerators and air-conditioners their whole lives and have never asked themselves how they work. Same principle! Compressor and expansion valve (and the heat-holding capacity of a phase change; another confusing one for people). thanks for helping educate! Hardwood Floors
This process involves treating the wood by boiling the log in water. After preparation, the wood is peeled by a blade starting from the outside of the log and working toward the center, thus creating a wood veneer. The veneer is then pressed flat with high pressure. This style of manufacturing tends to have problems with the wood cupping or curling back to its original shape. Rotary-peeled engineered hardwoods tend to have a plywood appearance in the grain.[3]
We had bought and installed this beautiful product in our downstairs a few years ago. It's now time to do the upstairs and the product was the same excellent value for the price. Arrived quicker than we needed, but gives it time to acclimate to our home. We will be using the same installer and he was happy we are ordering the same product from the same company. He was VERY impressed by the quality of the product last time. I'm excited to see the completed project as I love this wood on our main floor. Denver Hardwood Floors
Cut a new length of flooring to fit snugly into the space of the old board. It doesn't matter what kind of saw you use to repair your hardwood floors; just make sure the cuts are perfectly square. After trimming the board to length, turn it upside down and use a chisel to chop off the lower lip of the grooved edge (photo 5). That allows it to fit over the protruding tongue of the adjacent floorboard. Test-fit the new piece. If it's slightly lower than the surrounding floorboards, shim it up with strips of kraft paper. Then remove the board and spread carpenter's glue on the tongues and grooves of the new and old pieces. Slip the new board into place (photo 6), protect it with a scrap-wood block and tap it down with a hammer. Cover the board with wax paper, then hold it down overnight with heavy books or weights. An alternative to gluing: Simply face-nail the board with 6d finishing nails. Bore pilot holes at a slight angle, then drive in the nails. Tap them below the surface with a nailset (photo 7) and fill the holes with wood putty. Lightly sand the entire board smooth, but be careful not to remove too much finish from surrounding boards. After finding a matching stain color by experimenting on scraps of flooring, stain the boards to match the original floor. Let dry overnight, then apply two coats of clear polyurethane varnish. If the old floor is unstained, just apply the polyurethane. Denver Hardwood Flooring
Wood flooring can also be installed utilizing the glue-down method. This is an especially popular method for solid parquet flooring installations on concrete sub-floors. Additionally, engineered wood flooring may use the glue-down method as well. A layer of mastic is placed onto the sub-floor using a trowel similar to those used in laying ceramic tile. The wood pieces are then laid on top of the glue and hammered into place using a rubber mallet and a protected 2x4 to create a level floor. Often the parquet floor will require sanding and re-finishing after the glue-down installation method due to the small size pieces. Denver Hardwood Flooring
Some benefits of wood flooring include ease of cleaning, durability, and style variety. Wood floors are much easier to keep clean than carpet and pet hair or dander is quick to remove. They are very durable and with proper care, they will look great for years to come. Plus, wood flooring is available in a multitude of styles and colors guaranteeing there is a look out there for a classic or contemporary home. Denver Hardwood Floors
Cut a new length of flooring to fit snugly into the space of the old board. It doesn't matter what kind of saw you use to repair your hardwood floors; just make sure the cuts are perfectly square. After trimming the board to length, turn it upside down and use a chisel to chop off the lower lip of the grooved edge (photo 5). That allows it to fit over the protruding tongue of the adjacent floorboard. Test-fit the new piece. If it's slightly lower than the surrounding floorboards, shim it up with strips of kraft paper. Then remove the board and spread carpenter's glue on the tongues and grooves of the new and old pieces. Slip the new board into place (photo 6), protect it with a scrap-wood block and tap it down with a hammer. Cover the board with wax paper, then hold it down overnight with heavy books or weights. An alternative to gluing: Simply face-nail the board with 6d finishing nails. Bore pilot holes at a slight angle, then drive in the nails. Tap them below the surface with a nailset (photo 7) and fill the holes with wood putty. Lightly sand the entire board smooth, but be careful not to remove too much finish from surrounding boards. After finding a matching stain color by experimenting on scraps of flooring, stain the boards to match the original floor. Let dry overnight, then apply two coats of clear polyurethane varnish. If the old floor is unstained, just apply the polyurethane. Denver Hardwood Flooring
Solid hardwood flooring adds character, warmth and value to any room in your house. Our selection of pre-finished solid hardwood flooring offers you a variety of finishes, widths, lengths, and colors to match your style, whether it is rustic or modern. There are lots of choices including oak, walnut, maple, birch, cherry and exotic hardwoods. We offer exceptional hardwood floors that will help you enhance the look of your home. Denver Hardwood Floors
The natural process of things will tend to close gaps as the weather and humidity changes. As a rule, if the gap is less than the thickness of a dime, your flooring is normal and there’s nothing to worry about. If your gaps are more persistent, you might need to call in a professional to tighten up your hardwood floor so that they cease to be a problem. Denver Hardwood Floors
Make cuts perpendicular to the direction the wood is laying. Using a circular saw, make single cuts straight across the flooring that are about 1 foot (30 cm) to 2 feet (61 cm) apart. Be sure your cuts are perpendicular to the direction of the wood. Start on 1 side of the room and work your way systematically to the other side, spacing each cut about 1 foot (30 cm) to 2 feet (61 cm) apart.[3] Denver Hardwood Floors
Glue down engineered hardwood, alternatively. If you don't want to nail down the boards, you do have the option of using adhesive to put engineered hardwood in place. It's a good choice, but won't last as long or be as sturdy as nailed down hardwood. The procedure is very similar to the nail-down process. Follow the adhesive manufacturer's instructions for installation and drying times.[11] Hardwood Floors
Enhance your home with beautiful hardwood flooring that Enhance your home with beautiful hardwood flooring that fits your budget. Full of abundant character and color variation the Bruce Plano collection celebrates the beauty of natural hardwood. Enjoy natural features including mineral streaks knots and small holes and minor milling imperfections. Design your floor to your unique tastes with ...  More + Product Details Close
Awesome explanation! When I say heat pump to people, it's amazing how often their eyes glaze over...even though most of them have had refrigerators and air-conditioners their whole lives and have never asked themselves how they work. Same principle! Compressor and expansion valve (and the heat-holding capacity of a phase change; another confusing one for people). thanks for helping educate! Denver Hardwood Floor Install
Installing a hardwood floor yourself can save you money – if you know what you’re doing. Improper preparation and installation can lead to warping and buckling, which will ruin flooring that would otherwise remain beautiful for years to come. The most important thing you can do to ensure the structural integrity of your floor is to properly prepare for the installation process. Here are various articles to help you!
The Blue Ridge Hickory Morning Fog 3/4 in. The Blue Ridge Hickory Morning Fog 3/4 in. Solid Hardwood Flooring is sealed with an Alpha Alumina finish providing protection from every day wear. This product carries a 50-year finish warranty. Each plank features a micro beveled edge and micro beveled end. You can feel confident purchasing this product because ...  More + Product Details Close
If your floor has noticeable scratches throughout, your best option is to sand down the floor and refinish it. A complete sanding removes scratches, but beware: This only works on real wood floors, not bamboo. If you have an engineered wood floor with a real wood surface, make sure the real wood surface is more than 1mm thick—sanding usually takes at least this much wood off the surface, so a thicker layer is required for a complete sanding. Denver Hardwood Flooring
If your floors are in need of a deeper cleaning, use a wood floor cleaner. Follow the instructions for diluting the cleaner in water. Clean the floors with a damp mop, going with the grain. Then, go back over the floor with a clean, damp mop to remove any excess cleaner. Finish by drying the floor completely with a dry towel. Remember, leftover standing water could damage your wood floors. Hardwood Floors
Most floors use a tongue-and-groove design for connecting adjacent strips. This design makes replacing a single strip or plank challenging, but not impossible. First, look for any nails in the damaged board and drive them as far through the board as possible by using a hammer and nail set. Carpenters use nail sets to drive nails flush with trim without damaging the trim with a hammer. After you’ve cleared the nails, it’s time to remove the damaged board and install a new one. Follow these steps: Denver Hardwood Flooring
If your floor has noticeable scratches throughout, your best option is to sand down the floor and refinish it. A complete sanding removes scratches, but beware: This only works on real wood floors, not bamboo. If you have an engineered wood floor with a real wood surface, make sure the real wood surface is more than 1mm thick—sanding usually takes at least this much wood off the surface, so a thicker layer is required for a complete sanding.

Solid hardwood is great for high traffic areas and rooms on the first or second floors where there’s limited moisture. You can purchase your solid hardwood floors either prefinished or unfinished. Prefinished hardwood floors have a coating that protects them and they’re ready to install right out of the box. Unfinished hardwoods allow you to apply your own stain color. Denver Hardwood Flooring
Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7]
Engineered wood flooring was created to lower the cost of wood flooring and attempt to fix some of solid wood’s shortcomings. It’s constructed from inexpensive plywood or particle board and topped with a thin veneer of hardwood. This construction helps with installation flexibility and slightly improves indent performance, but it adds a new set of problems as well. Because the “real” wood part of the floor is just a thin veneer, damage from scratches can be irreparable. Engineered wood floors are still made from porous wood, meaning they can’t be subjected to water. Denver Hardwood Flooring
Nothing compares with the beauty of genuine hardwood floors (especially when they're maintained well). Whether engineered hardwood or solid hardwood flooring, the glow of natural wood brings comfort and beauty to any room. Wayfair carries thousands of species of natural wood flooring, including oak, hickory, maple, cherry, birch, cork, bamboo, and exotic hardwood species. If you're new to wood flooring, read our guide that has everything you need to know. Denver Hardwood Floor Install
Rigid Core flooring is a category of resilient flooring, and it has been designed from the ground up with modern homes in mind. It’s 100% waterproof, easy to install, and provides extreme scratch and indent resistance when compared to solid or engineered wood flooring. It also offers a wide range of design options because it isn’t limited to traditional wood species. Its hybrid visuals, exotic species, colors, and textures go above and beyond anything traditional wood flooring can offer. Denver Hardwood Floors
If you face medium scratches that show only slight damage, you may be apply to apply a new coat of finish to the area without having to refinish the floor entirely. Make sure the finish matches the original as closely as possible. If the wood was stained but has no finish, you may be able to get similar wood floor scratch repair results by re-applying the stain to help hide the scratch.

Floating installation: A floating installation is where the flooring is laid down in a glueless manner on top of a layer of underlay. The individual planks are locked together, and are not glued or nailed down to the subfloor. By doing this the floor is floating above the underlay, and can be laid on top of existing tile or marble, without the risk of damaging the subflooring. Denver Hardwood Flooring

This process begins with the same treatment process that the rotary peel method uses. However, instead of being sliced in a rotary fashion, with this technique the wood is sliced from the log in much the same manner that lumber is sawn from a log – straight through. The veneers do not go through the same manufacturing process as rotary peeled veneers. Engineered hardwood produced this way tends to have fewer problems with "face checking", and also does not have the same plywood appearance in the grain.[3] However, the planks can tend to have edge splintering and cracking because the veneers have been submerged in water and then pressed flat. Denver Hardwood Floor Install
It is difficult to compare solid wood flooring to engineered wood flooring due to the wide range of quality in both product categories, particularly engineered. Solid wood has some limitations. Recommended maximum widths and lengths are typically 5" / 127mm wide and 7' / 2100mm long. Solid hardwood is also more prone to "gapping" (excessive space between planks), "crowning" (convex curving upwards when humidity increases) and "cupping" (a concave or "dished" appearance of the plank, with the height of the plank along its longer edges being higher than the centre) with increased plank size. Solid wood cannot be used with underfloor radiant heating.[5] However extra care is necessary with the planning and installation of the heating system and the wood flooring, such as limiting the temperature to 85 °F (29 °C), avoid sharp temperature fluctuations, utilizing an outdoor thermostat to anticipate heating demands, and monitoring the moisture content for the subfloor before installation. Denver Hardwood Floor Install
Instead of boiling the hardwood logs, in this process they are kept at a low humidity level and dried slowly to draw moisture from the inside of the wood cells. The logs are then sawn in the same manner as for solid hardwood planks. This style of engineered hardwood has the same look as solid hardwood, and does not have any of the potential problems of "face checking" that rotary-peel and slice-peel products have, because the product is not exposed to added moisture. Denver Hardwood Flooring
A number of proprietary features for solid wood floors are available. Many solid woods come with grooves cut into the back of the wood that run the length of each plank, often called 'absorption strips,' that are intended to reduce cupping. Solid wood floors are mostly manufactured 0.75 inches (19 mm) thick with a tongue-and-groove for installation. Denver Hardwood Flooring
Engineered wood flooring has other benefits beyond dimensional stability and universal use. Patented installation systems allow for faster installation and easy replacement of boards. Engineered wood also allows for a floating installation where the planks are not adhered to the subfloor or to each other, further increasing ease of repair and reducing installation time. Engineered flooring is also suitable for underfloor and radiant heating systems.
If you have a small, single scratch that’s only noticeable when you get close (like a scratch caused by an excited pet) and your floor has a relatively new finish, try a DIY home solution first. Mix equal parts apple cider vinegar and olive oil in a small cup, and dab the mixture into the scratch. Leave it for the rest of the day, and rub it out. This method often takes care of minor scratches.
Floor connection system: There are a wide range of connection systems, as most of them are mill-specific manufacturing techniques. The general principle is to have grooves on all four sides of the plank with a separate, unconnected, piece that is inserted into the grooves of two planks to join them. The piece used for the connection can be made from wood, rubber, or plastic. This installation system allows for different materials (i.e. wood and metal) to be installed together if they have the same connection system. Denver Hardwood Floor Install
Engineered wood flooring was created to lower the cost of wood flooring and attempt to fix some of solid wood’s shortcomings. It’s constructed from inexpensive plywood or particle board and topped with a thin veneer of hardwood. This construction helps with installation flexibility and slightly improves indent performance, but it adds a new set of problems as well. Because the “real” wood part of the floor is just a thin veneer, damage from scratches can be irreparable. Engineered wood floors are still made from porous wood, meaning they can’t be subjected to water. Denver Hardwood Floors
 Bamboo Flooring (22)  BELLAWOOD (49)  BELLAWOOD Artisan Distressed (13)  BELLAWOOD Artisan Distressed Engineered (4)  BELLAWOOD Engineered (16)  Builders Pride (26)  Builder's Pride (10)  Builder's Pride Engineered (1)  Clover Lea (9)  Major Brand (5)  Mayflower (12)  Mayflower Engineered (19)  R.L. Colston (40)  Virginia Mill Works (8)  Virginia Mill Works Engineered (21)
It’s important to start by knowing what kind of finish is on your floor. Is your finish oil or water based? Do you have a wax coating? Is the wood varnished or stained? Is there an aluminum oxide coating? Know what the surface is made of so you know how to start your wood floor scratch repair. If you didn’t install the floor and aren’t sure what type of finish it has, you can check here for more details on identifying it.
Most floors use a tongue-and-groove design for connecting adjacent strips. This design makes replacing a single strip or plank challenging, but not impossible. First, look for any nails in the damaged board and drive them as far through the board as possible by using a hammer and nail set. Carpenters use nail sets to drive nails flush with trim without damaging the trim with a hammer. After you’ve cleared the nails, it’s time to remove the damaged board and install a new one. Follow these steps: Denver Hardwood Floor Install
Glue down engineered hardwood, alternatively. If you don't want to nail down the boards, you do have the option of using adhesive to put engineered hardwood in place. It's a good choice, but won't last as long or be as sturdy as nailed down hardwood. The procedure is very similar to the nail-down process. Follow the adhesive manufacturer's instructions for installation and drying times.[11] Hardwood Floors
×