If your floors are in need of a deeper cleaning, use a wood floor cleaner. Follow the instructions for diluting the cleaner in water. Clean the floors with a damp mop, going with the grain. Then, go back over the floor with a clean, damp mop to remove any excess cleaner. Finish by drying the floor completely with a dry towel. Remember, leftover standing water could damage your wood floors.
Solid hardwood floors are made of planks milled from a single piece of timber. Solid hardwood floors were originally used for structural purposes, being installed perpendicular to the wooden support beams of a building known as joists or bearers. With the increased use of concrete as a subfloor in some parts of the world, engineered wood flooring has gained some popularity. However, solid wood floors are still common and popular. Solid wood floors have a thicker wear surface and can be sanded and finished more times than an engineered wood floor.[2] It is not uncommon for homes in New England, Eastern Canada, USA, and Europe to have the original solid wood floor still in use today. Denver Hardwood Flooring

Cut a new length of flooring to fit snugly into the space of the old board. It doesn't matter what kind of saw you use to repair your hardwood floors; just make sure the cuts are perfectly square. After trimming the board to length, turn it upside down and use a chisel to chop off the lower lip of the grooved edge (photo 5). That allows it to fit over the protruding tongue of the adjacent floorboard. Test-fit the new piece. If it's slightly lower than the surrounding floorboards, shim it up with strips of kraft paper. Then remove the board and spread carpenter's glue on the tongues and grooves of the new and old pieces. Slip the new board into place (photo 6), protect it with a scrap-wood block and tap it down with a hammer. Cover the board with wax paper, then hold it down overnight with heavy books or weights. An alternative to gluing: Simply face-nail the board with 6d finishing nails. Bore pilot holes at a slight angle, then drive in the nails. Tap them below the surface with a nailset (photo 7) and fill the holes with wood putty. Lightly sand the entire board smooth, but be careful not to remove too much finish from surrounding boards. After finding a matching stain color by experimenting on scraps of flooring, stain the boards to match the original floor. Let dry overnight, then apply two coats of clear polyurethane varnish. If the old floor is unstained, just apply the polyurethane. Denver Hardwood Flooring
Lowe’s has what you need to bring value-adding beauty to your home with hardwood flooring. There are plenty of species to choose from, including acacia wood flooring, walnut flooring, maple flooring, hickory hardwood flooring and cherry wood flooring. Depending on your budget and room’s traffic level, you’ll be sure to find a style to suit your needs. Denver Hardwood Flooring

The Home Depot offers a stunning selection of solid wood and engineered flooring that is sustainably sourced to help preserve our world’s endangered forests. Installation services are available for homes of all sizes. Licensed, certified, and vetted with background checks, our professional installers show up wearing an official Home Depot badge, so you’ll know we sent them. We are transparent about our products, so you know exactly what’s being installed in your home. To help you create your dream home sooner, The Home Depot also offers financial assistance options like project loans and specialty credit cards.
 116% harder than Red Oak (1)  12% harder than Red Oak (11)  123% Harder than Red Oak (4)  125% harder than Red Oak (2)  141% harder than Red Oak (2)  15% softer than Red Oak (2)  165% harder than Red Oak (2)  174% harder than Red Oak (5)  18% softer than Red Oak (1)  185% harder than Red Oak (4)  198 % harder than Red Oak (2)  2% harder than Red Oak (2)  2% Softer than Red Oak (1)  25% softer than Red Oak (1)  28% harder than Red Oak (1)  30% harder than Red Oak (8)  33% harder than Red Oak (2)  41% harder than Red Oak (7)  43% harder than Red Oak (1)  5% harder than Red Oak (8)  53% softer than Red Oak (1)  6% harder than Red Oak (14)  67% harder than Red Oak (5)  74% harder than Red Oak (2)  81% harder than Red Oak (2)  82% harder than Red Oak (2)  9% softer than Red Oak (1)  about the same as Red Oak (7)  Benchmark at 1290 on Janka Scale (37) Denver Hardwood Flooring
The Home Depot offers a stunning selection of solid wood and engineered flooring that is sustainably sourced to help preserve our world’s endangered forests. Installation services are available for homes of all sizes. Licensed, certified, and vetted with background checks, our professional installers show up wearing an official Home Depot badge, so you’ll know we sent them. We are transparent about our products, so you know exactly what’s being installed in your home. To help you create your dream home sooner, The Home Depot also offers financial assistance options like project loans and specialty credit cards. Hardwood Floors
Start by cleaning the entire area around the scratch. You will want to remove all traces of dust and grime on the floor before you begin any other steps. Pay close attention to the inside of the crack itself, which should be totally free of dirt, if possible. If you have a wax layer, use a wax remover solution to clear away the wax before you begin the repair.
This durable prefinished solid real wood floor will This durable prefinished solid real wood floor will enhance the value of your home. The flooring is made of 3/4 in. thick sawn solid wood and features mother nature's naturally occurring beauty marks such as distinctive color variation knots and mineral streaks. Plank length is totally random and varies based ...  More + Product Details Close Denver Hardwood Floors
Jasper, Mazama, and the other brands of hardwood flooring we offer are premium quality, delivering everything you want in a hardwood floor - look, strength, durability, and ongoing value for properties. And we offer them to you at incredible pricing not found anywhere else. While we sell discount hardwood flooring, we will never sell cheap hardwood flooring. All of our products undergo rigorous product quality testing before we offer them to you and they are constantly rechecked for quality to ensure you always get the best products while still paying below wholesale prices. Denver Hardwood Floor Install
This durable prefinished solid real wood floor will This durable prefinished solid real wood floor will enhance the value of your home. The flooring is made of 3/4 in. thick sawn solid wood and features mother nature's naturally occurring beauty marks such as distinctive color variation knots and mineral streaks. Plank length is totally random and varies based ...  More + Product Details Close Denver Hardwood Flooring
Engineered wood flooring was created to lower the cost of wood flooring and attempt to fix some of solid wood’s shortcomings. It’s constructed from inexpensive plywood or particle board and topped with a thin veneer of hardwood. This construction helps with installation flexibility and slightly improves indent performance, but it adds a new set of problems as well. Because the “real” wood part of the floor is just a thin veneer, damage from scratches can be irreparable. Engineered wood floors are still made from porous wood, meaning they can’t be subjected to water. Denver Hardwood Flooring

Maple is another great choice for hardwood flooring. Many people prefer its light tan look, which blends into home interior spaces. As one of the strongest woods, maple is a top choice for high-traffic areas of a home. The wood doesn’t scuff easily, making it a good choice for homes with children or those with a lot of foot traffic across the floors. Maple requires minimal maintenance, with weekly sweeping and annual applications of wood soap to prolong the life of the floors.
If you face medium scratches that show only slight damage, you may be apply to apply a new coat of finish to the area without having to refinish the floor entirely. Make sure the finish matches the original as closely as possible. If the wood was stained but has no finish, you may be able to get similar wood floor scratch repair results by re-applying the stain to help hide the scratch.

Engineered wood flooring has other benefits beyond dimensional stability and universal use. Patented installation systems allow for faster installation and easy replacement of boards. Engineered wood also allows for a floating installation where the planks are not adhered to the subfloor or to each other, further increasing ease of repair and reducing installation time. Engineered flooring is also suitable for underfloor and radiant heating systems. Denver Hardwood Floors
If your only goal is to brighten your floors and restore their original shine, consider refinishing them. But if you want to change some aspect of the floor itself, like the style of the wood, the direction of the planks or the consistency of the material, you will need to invest in a full replacement. Refinishing is ideal to restore existing wood, while replacement is ideal for establishing a completely new look or feel. Denver Hardwood Floor Install
Hardwood species used in flooring are given a hardwood hardness rating, which indicates how resistant the wood is to dents and wear. This rating is based off a test called the Janka Hardness Test, and it measures the force needed to press a steel ball into the wood sample. The highest possible score on this test is a little over 5,000, with most traditional solid wood floors scoring in the 1,000-2,000 range. The superior density of Rigid Core flooring would exceed the limitations of the Janka test, and instead a higher impact testing is needed to measure real world performance. Here is how the general hardness of plank flooring ranks: Denver Hardwood Floors
Generally, hardwood floors need to be buffed every 3–5 years. The process usually takes about one day. Buffing refers to the process of using a stand up floor buffer. The floor is abraded with 180 grit screen on the buffer. This allows for the new coat of finish to mechanically adhere to the floor. This process works with great results as long as the floor hasn't had any waxes or synthetic cleaners. Denver Hardwood Floor Install

Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7] Denver Hardwood Floor Install

It can be sanded down and refinished five, six, even seven times. And, if maintained properly, you won’t have to do it for 20 years. Refinishing a floor may be messy and troublesome, but most homeowners learn to live with it. After all, it costs five times as much to replace hardwood floors than it does to refinish them. For some people that is reason enough. Denver Hardwood Floor Install
If you have a small, single scratch that’s only noticeable when you get close (like a scratch caused by an excited pet) and your floor has a relatively new finish, try a DIY home solution first. Mix equal parts apple cider vinegar and olive oil in a small cup, and dab the mixture into the scratch. Leave it for the rest of the day, and rub it out. This method often takes care of minor scratches. Denver Hardwood Floors
Wood floors offer warmth and enhance the look of your rooms while increasing the value of your home. Wood flooring comes in a variety of styles and materials from solid hardwood to engineered hardwood to bamboo. You’ll find wooden floors also comes in a number of shades. In addition to looking great, wood floors are durable making them perfect for homes with pets and children.
Refinish, refinish, refinish! In almost every case it is preferable to refinish rather than replace hardwood floors. Part of the appeal of hardwood is that it lasts so long. A quality hardwood floor can be sanded down and refinished at least six times, and up to ten times before you need to replace it. You can change the color, closely match and replace warped, stained, or termite ingested planks, silence squeaky boards, and fill gaps or patch knots. With all of these easy solutions, why would anyone choose to replace hardwood floors? Well, here are the cases when a complete rehaul becomes a better option. Denver Hardwood Flooring
Hardwood can match any décor, from traditional light wood floors to trendy white wood flooring, grey wood floors and dark wood floors. Start with unfinished hard wood flooring boards to create a blank canvas for stain and unique design. We also have hand-scraped hardwood and distressed wood flooring to add a rustic, timeworn look. A wide plank wood flooring can also make a room feel bigger and more modern. Hardwood flooring also has DIY installation that’s easy with tongue and groove flooring options. Denver Hardwood Floors
A buckled floor happens when the boards warp and lift up from the subfloor that they are attached to. You’ll most likely need to call in a hardwood floor installer to identify the root of the problem if buckling is an issue. Once the cause of your buckling has been identified, you’ll need to take the necessary measures to ensure that your hardwood planks are firmly attached to the subfloor so that the problem no longer persists.
If your floors are in need of a deeper cleaning, use a wood floor cleaner. Follow the instructions for diluting the cleaner in water. Clean the floors with a damp mop, going with the grain. Then, go back over the floor with a clean, damp mop to remove any excess cleaner. Finish by drying the floor completely with a dry towel. Remember, leftover standing water could damage your wood floors. Denver Hardwood Flooring
Cut a new length of flooring to fit snugly into the space of the old board. It doesn't matter what kind of saw you use to repair your hardwood floors; just make sure the cuts are perfectly square. After trimming the board to length, turn it upside down and use a chisel to chop off the lower lip of the grooved edge (photo 5). That allows it to fit over the protruding tongue of the adjacent floorboard. Test-fit the new piece. If it's slightly lower than the surrounding floorboards, shim it up with strips of kraft paper. Then remove the board and spread carpenter's glue on the tongues and grooves of the new and old pieces. Slip the new board into place (photo 6), protect it with a scrap-wood block and tap it down with a hammer. Cover the board with wax paper, then hold it down overnight with heavy books or weights. An alternative to gluing: Simply face-nail the board with 6d finishing nails. Bore pilot holes at a slight angle, then drive in the nails. Tap them below the surface with a nailset (photo 7) and fill the holes with wood putty. Lightly sand the entire board smooth, but be careful not to remove too much finish from surrounding boards. After finding a matching stain color by experimenting on scraps of flooring, stain the boards to match the original floor. Let dry overnight, then apply two coats of clear polyurethane varnish. If the old floor is unstained, just apply the polyurethane.
Engineered wood flooring has other benefits beyond dimensional stability and universal use. Patented installation systems allow for faster installation and easy replacement of boards. Engineered wood also allows for a floating installation where the planks are not adhered to the subfloor or to each other, further increasing ease of repair and reducing installation time. Engineered flooring is also suitable for underfloor and radiant heating systems. Hardwood Floors
Before you choose a hardwood floor, think about how much foot traffic you expect. Consider the look you want and how much you plan to invest. And, if you’re still undecided, browse our selection of other flooring options, including vinyl flooring, tile, parquet, and laminate flooring. You can also find helpful information in our cost guide. From selection to delivery and installation, the Home Depot is your one-stop shop for all your flooring needs.
It is difficult to compare solid wood flooring to engineered wood flooring due to the wide range of quality in both product categories, particularly engineered. Solid wood has some limitations. Recommended maximum widths and lengths are typically 5" / 127mm wide and 7' / 2100mm long. Solid hardwood is also more prone to "gapping" (excessive space between planks), "crowning" (convex curving upwards when humidity increases) and "cupping" (a concave or "dished" appearance of the plank, with the height of the plank along its longer edges being higher than the centre) with increased plank size. Solid wood cannot be used with underfloor radiant heating.[5] However extra care is necessary with the planning and installation of the heating system and the wood flooring, such as limiting the temperature to 85 °F (29 °C), avoid sharp temperature fluctuations, utilizing an outdoor thermostat to anticipate heating demands, and monitoring the moisture content for the subfloor before installation. Denver Hardwood Flooring

Jasper, Mazama, and the other brands of hardwood flooring we offer are premium quality, delivering everything you want in a hardwood floor - look, strength, durability, and ongoing value for properties. And we offer them to you at incredible pricing not found anywhere else. While we sell discount hardwood flooring, we will never sell cheap hardwood flooring. All of our products undergo rigorous product quality testing before we offer them to you and they are constantly rechecked for quality to ensure you always get the best products while still paying below wholesale prices.


Menards® has everything you need to cover your floors in style! We offer a wide selection of hardwood flooring options that are fit to use in any room of your home. Some of our quality hardwood floorcoverings include engineered hardwood, which is built to last and has higher resistance to moisture levels. We also carry a variety of solid hardwood flooring to give your home traditional character and style. If you are interested in another durable flooring option for your home, we have cork flooring. In addition to strong and durable flooring, we offer everything you will need for installation and maintenance as well as hardwood moulding and trims to help you finish the job. Once the flooring installation is complete, keep them looking clean with our selection of vacuum cleaners and floor care products. Next, complete the look with area rugs, mats, and runners to enhance your home's décor and add coziness to the space.

We had bought and installed this beautiful product in our downstairs a few years ago. It's now time to do the upstairs and the product was the same excellent value for the price. Arrived quicker than we needed, but gives it time to acclimate to our home. We will be using the same installer and he was happy we are ordering the same product from the same company. He was VERY impressed by the quality of the product last time. I'm excited to see the completed project as I love this wood on our main floor.
If you face medium scratches that show only slight damage, you may be apply to apply a new coat of finish to the area without having to refinish the floor entirely. Make sure the finish matches the original as closely as possible. If the wood was stained but has no finish, you may be able to get similar wood floor scratch repair results by re-applying the stain to help hide the scratch. Denver Hardwood Flooring

Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7] Denver Hardwood Floors


We had bought and installed this beautiful product in our downstairs a few years ago. It's now time to do the upstairs and the product was the same excellent value for the price. Arrived quicker than we needed, but gives it time to acclimate to our home. We will be using the same installer and he was happy we are ordering the same product from the same company. He was VERY impressed by the quality of the product last time. I'm excited to see the completed project as I love this wood on our main floor. Hardwood Floors

×