Not only is bamboo resistant to moisture, but it is environmentally friendly and an optimal choice for those who are looking to build “green.” The plant grows faster and does not take as long to re-grow than a typical hardwood tree, therefore not contributing to deforestation. Bamboo flooring is softer than traditional hardwoods, so it will not cause pain if it is stood on for long periods of time. The softness of the floor will also reduce noise. Denver Hardwood Floors
You may be on the fence about your decision to refinish your hardwood floors because you wonder if your floors are a candidate for refinishing. The truth is, not all hardwood floors can be refinished. Although most common problems can be addressed and fixed without replacing the entire floor, there are some exceptions. Consider the following to make an informed decision. Hardwood Floors
Floating installation: A floating installation is where the flooring is laid down in a glueless manner on top of a layer of underlay. The individual planks are locked together, and are not glued or nailed down to the subfloor. By doing this the floor is floating above the underlay, and can be laid on top of existing tile or marble, without the risk of damaging the subflooring.
Tongue-and-groove: One side and one end of the plank have a groove, the other side and end have a tongue (protruding wood along an edge's center). The tongue and groove fit snugly together, thus joining or aligning the planks, and are not visible once joined. Tongue-and-groove flooring can be installed by glue-down (both engineered and solid), floating (mostly engineered only), or nail-down (not recommended for most engineered). Hardwood Floors

Cupped floors, also called washboarding, develops gradually across the width of the wood strip where the edges of the hardwood planks raise up and the center of the board sinks down. The cause of cupped floors is a moisture imbalance where there is more water on the bottom side of the wood plank than on the top. The only cure is to balance the humidity levels in your home, and to give the surface time to return back to normal. After the floor has stabilized, you can have a professional sand it flat and re-finish it to perfection.


Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7] Denver Hardwood Floors
Add style, warmth, and value to your home with beautiful hardwood floors from The Home Depot. Our hardwood floors are available in solid and engineered hardwood, and a wide variety of colors, styles and wood species. Whether you’re interested in a traditional look, like a classic oak wood floor or something more modern and contemporary, like bamboo floors or cork flooring, we have everything you need to get your flooring project done. Hardwood Floors
 Acacia (9)  American Walnut (1)  Ash (5)  Bamboo (22)  Beech (5)  Birch (3)  Bloodwood (2)  Brazilian Cherry (10)  Brazilian Chestnut (5)  Brazilian Koa (9)  Brazilian Oak (5)  Brazilian Walnut (5)  Cumaru (3)  Curupay (2)  Hevea (4)  Hickory (27)  Maple (14)  Oak (15)  Pecan (3)  Pine (10)  Purple Heart (2)  Red Cumaru (2)  Red Maple (1)  Red Oak (40)  Short Leaf Acacia (3)  ShortLeaf Acacia (1)  Spanish Hickory (3)  Tamboril (2)  Tauari (3)  Walnut (1)  White Oak (34) Denver Hardwood Floors
Because tongue-and-groove boards are locked in place, removal involves cutting out the middle of each damaged board. The easiest way is to bore a 1-in.-dia. hole through both ends of each damaged board (photo 1). Then use a circular saw to connect the two holes (photo 2). Follow these steps to safely make the plunge cuts you need to repair your hardwood floors: 1. Adjust the depth of cut to the thickness of the floorboards. Plug in the saw and put on eye protection. 2. Pull back the retractable blade guard with your thumb. Then hold the nose of the baseplate on the floorboard and lift up the rear of the saw. 3. Align the blade with the right edge of one of the holes. Make sure the blade isn't touching the floor, then squeeze the trigger and slowly lower the spinning blade into the board. 4. Grip the saw firmly with both hands and guide it in a straight line until you cut into the right edge of the hole at the opposite end of the board. 5. Move back to the first hole, align the blade with the left edge and cut to the left edge of the second hole. Pry out the middle section with a hammer and chisel. Chop out the remaining edges, being careful not to damage any surrounding boards (photo 3). The "tongue" piece will be nailed in place, so break it out in small pieces. Then pull out the nails with a hammer or locking pliers. The existing floorboards have a tongue and groove milled on each end and along the edges. Chop off the tongue exposed by the board you just removed so you can slip in the new board (photo 4).
 Bamboo Flooring (22)  BELLAWOOD (49)  BELLAWOOD Artisan Distressed (13)  BELLAWOOD Artisan Distressed Engineered (4)  BELLAWOOD Engineered (16)  Builders Pride (26)  Builder's Pride (10)  Builder's Pride Engineered (1)  Clover Lea (9)  Major Brand (5)  Mayflower (12)  Mayflower Engineered (19)  R.L. Colston (40)  Virginia Mill Works (8)  Virginia Mill Works Engineered (21) Hardwood Floors
This durable prefinished solid real wood floor will This durable prefinished solid real wood floor will enhance the value of your home. The flooring is made of 3/4 in. thick sawn solid wood and features mother nature's naturally occurring beauty marks such as distinctive color variation knots and mineral streaks. Plank length is totally random and varies based ...  More + Product Details Close Denver Hardwood Floors
Start by cleaning the entire area around the scratch. You will want to remove all traces of dust and grime on the floor before you begin any other steps. Pay close attention to the inside of the crack itself, which should be totally free of dirt, if possible. If you have a wax layer, use a wax remover solution to clear away the wax before you begin the repair.
Laminate is a cost effective option that will withstand a certain amount of wear. For an easy installation, opt for click-lock. The planks will snap together and can be laid over other flooring. It is ideal for living areas, and some brands may even construct it with a waterproof core, allowing it to be used in areas where water may be an issue. We suggest taking a close look at the guarantee before installing it in a bathroom. Hardwood Floors
×