Cupped floors, also called washboarding, develops gradually across the width of the wood strip where the edges of the hardwood planks raise up and the center of the board sinks down. The cause of cupped floors is a moisture imbalance where there is more water on the bottom side of the wood plank than on the top. The only cure is to balance the humidity levels in your home, and to give the surface time to return back to normal. After the floor has stabilized, you can have a professional sand it flat and re-finish it to perfection. Hardwood Floors
Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7] Hardwood Floors
Visual – While hardwood flooring is limited by species and stains, Rigid Core flooring has near limitless options when it comes to flooring that looks like wood. In addition to traditional wood visuals and colors, you can pick from stone looks and even hybrids that marry wood and stones together into unique new options. And best of all you will benefit from a curated look that removes unwanted imperfections like oversized knots, holes, and worming that naturally occurs in hardwood floors. Denver Hardwood Floor Install
There are some characteristics that are common to each category: solid wood is more frequently site-finished, is always in a plank format, is generally thicker than engineered wood, and is usually installed by nailing. Engineered wood is more frequently pre-finished, has bevelled edges, is very rarely site-finished, and is installed with glue or as a floating installation. [6]
Generally, hardwood floors need to be buffed every 3–5 years. The process usually takes about one day. Buffing refers to the process of using a stand up floor buffer. The floor is abraded with 180 grit screen on the buffer. This allows for the new coat of finish to mechanically adhere to the floor. This process works with great results as long as the floor hasn't had any waxes or synthetic cleaners. Denver Hardwood Floor Install
Warped hardwood floors, also known as sagging, is a serious problem for any homeowner. It is often the result of serious moisture problems, and any evidence of warped hardwood floors needs to be addressed immediately. Warped hardwood floors are rarely the result of faulty hardwood or installation, but are a symptom of larger moisture problems in the home itself that need to be taken care of. Denver Hardwood Floors
There are some characteristics that are common to each category: solid wood is more frequently site-finished, is always in a plank format, is generally thicker than engineered wood, and is usually installed by nailing. Engineered wood is more frequently pre-finished, has bevelled edges, is very rarely site-finished, and is installed with glue or as a floating installation. [6] Hardwood Floors

Solid hardwood is great for high traffic areas and rooms on the first or second floors where there’s limited moisture. You can purchase your solid hardwood floors either prefinished or unfinished. Prefinished hardwood floors have a coating that protects them and they’re ready to install right out of the box. Unfinished hardwoods allow you to apply your own stain color. Denver Hardwood Floors
Another common hardwood floor malady is the development of gaps between planks. The most common causes of gaps between the boards is Mother Nature. Wood shrinks as it dries out, and it expands when it gets wet and humid. That regular expansion and contraction over time is the most common cause of gaps, and is the main reason why most gaps are seasonal in nature. Perhaps your best plan of action is to exercise patience. Denver Hardwood Floors
Glue down engineered hardwood, alternatively. If you don't want to nail down the boards, you do have the option of using adhesive to put engineered hardwood in place. It's a good choice, but won't last as long or be as sturdy as nailed down hardwood. The procedure is very similar to the nail-down process. Follow the adhesive manufacturer's instructions for installation and drying times.[11] Denver Hardwood Floor Install

"Click" or Woodloc systems: there are a number of patented "click" systems that now exist. These click systems are either "unilin" or "fiboloc" A "click" floor is similar to tongue-and-groove, but instead of fitting directly into the groove, the board must be angled or "tapped" in to make the curved or barbed tongue fit into the modified groove. No adhesive is used when installing a "click" floor, making board replacement easier. This system not only exists for engineered wood floors but also engineered bamboo and a small number of solid floors (such as "parador solido click") and is designed to be used for floating installations. It is beneficial for the Do-It-Yourself market. Denver Hardwood Floors
Wood flooring can also be installed utilizing the glue-down method. This is an especially popular method for solid parquet flooring installations on concrete sub-floors. Additionally, engineered wood flooring may use the glue-down method as well. A layer of mastic is placed onto the sub-floor using a trowel similar to those used in laying ceramic tile. The wood pieces are then laid on top of the glue and hammered into place using a rubber mallet and a protected 2x4 to create a level floor. Often the parquet floor will require sanding and re-finishing after the glue-down installation method due to the small size pieces. Denver Hardwood Floor Install
Choosing teak for your hardwood floors can be a smart choice. You’ll find teak is resistant to pests, as the natural oils found in the wood are undesirable to most insects, including termites. Teak is also a water-resistant wood choice, a bonus if you have young, active children or pets that come indoors soaking wet after walks in the rain. Teak bears an attractive reddish-brown color. However, if left untreated, teak can turn a silver color if exposed to UV rays of sunlight. To prevent discoloration and wear, you can treat the wood with a coating of oil to seal it so that you can enjoy beautiful teak floors for years to come. Denver Hardwood Floor Install
Solid hardwood floors are made of planks milled from a single piece of timber. Solid hardwood floors were originally used for structural purposes, being installed perpendicular to the wooden support beams of a building known as joists or bearers. With the increased use of concrete as a subfloor in some parts of the world, engineered wood flooring has gained some popularity. However, solid wood floors are still common and popular. Solid wood floors have a thicker wear surface and can be sanded and finished more times than an engineered wood floor.[2] It is not uncommon for homes in New England, Eastern Canada, USA, and Europe to have the original solid wood floor still in use today. Denver Hardwood Flooring
Warped hardwood floors, also known as sagging, is a serious problem for any homeowner. It is often the result of serious moisture problems, and any evidence of warped hardwood floors needs to be addressed immediately. Warped hardwood floors are rarely the result of faulty hardwood or installation, but are a symptom of larger moisture problems in the home itself that need to be taken care of.

Price is the first obvious variable to consider. It is almost always cheaper to refinish your floor than to replace it. When replacing, you must consider the cost of the new wood as well as the installation. You can offset much of this cost by installing the floor yourself, but this is a very invasive process that requires specialized knowledge and precision. You can typically refinish a wood floor yourself, with just a few inexpensive solutions. Denver Hardwood Flooring


The Home Depot offers a stunning selection of solid wood and engineered flooring that is sustainably sourced to help preserve our world’s endangered forests. Installation services are available for homes of all sizes. Licensed, certified, and vetted with background checks, our professional installers show up wearing an official Home Depot badge, so you’ll know we sent them. We are transparent about our products, so you know exactly what’s being installed in your home. To help you create your dream home sooner, The Home Depot also offers financial assistance options like project loans and specialty credit cards. Hardwood Floors
Choose your replacement hardwood flooring. You don't have to replace your old floor with the exact same wood or flooring type that you just removed! You can glue your new hardwood flooring into place if you like. You can also install nail-down, floating (or locking) hardwood flooring as a replacement. The choice is up to you and what your budget allows. Hardwood Floors
A buckled floor happens when the boards warp and lift up from the subfloor that they are attached to. You’ll most likely need to call in a hardwood floor installer to identify the root of the problem if buckling is an issue. Once the cause of your buckling has been identified, you’ll need to take the necessary measures to ensure that your hardwood planks are firmly attached to the subfloor so that the problem no longer persists.

To fix a buckled floorboard, you need to be able to access the floor from below. The way to tackle this problem is to put weight on the buckled area from above — a cement block works well. Then install a 1 1/4-inch screw in the buckled flooring from below. Allow the screw to penetrate only halfway into the flooring, or it may come up through the finished surface. Driving the screw through the subfloor and into the flooring pulls the flooring down against the subfloor and gets rid of the buckled spot. Denver Hardwood Floor Install
For example, moisture can be a factor, as variations in moisture can lead to gapping and warping. For this reason, installing hardwood flooring in full bathrooms is not recommended because of the fluctuating moisture levels. Follow manufacturer recommendations relating to moisture before selecting and installing hardwood. For more protection against moisture, use a moisture barrier.
Enhance your home with beautiful hardwood flooring that Enhance your home with beautiful hardwood flooring that fits your budget. Full of abundant character and color variation Bruce Plano Gunstock Oak celebrates the beauty of natural hardwood. Enjoy natural features including mineral streaks knots and small holes and minor milling imperfections. Design your floor to your unique tastes with ...  More + Product Details Close Denver Hardwood Flooring
Before you choose a hardwood floor, think about how much foot traffic you expect. Consider the look you want and how much you plan to invest. And, if you’re still undecided, browse our selection of other flooring options, including vinyl flooring, tile, parquet, and laminate flooring. You can also find helpful information in our cost guide. From selection to delivery and installation, the Home Depot is your one-stop shop for all your flooring needs.

Hardwood floors can last a long time, but eventually they need to be replaced. Luckily, it's a pretty straightforward process! Use a circular saw to cut the old hardwood into pieces, then remove the old flooring. Prepare your subflooring so that it's clean and perfectly level. After that, choose your replacement flooring and follow the process for installing that particular type of hardwood!
Warped hardwood floors, also known as sagging, is a serious problem for any homeowner. It is often the result of serious moisture problems, and any evidence of warped hardwood floors needs to be addressed immediately. Warped hardwood floors are rarely the result of faulty hardwood or installation, but are a symptom of larger moisture problems in the home itself that need to be taken care of.
If your floor has noticeable scratches throughout, your best option is to sand down the floor and refinish it. A complete sanding removes scratches, but beware: This only works on real wood floors, not bamboo. If you have an engineered wood floor with a real wood surface, make sure the real wood surface is more than 1mm thick—sanding usually takes at least this much wood off the surface, so a thicker layer is required for a complete sanding. Hardwood Floors
Make cuts perpendicular to the direction the wood is laying. Using a circular saw, make single cuts straight across the flooring that are about 1 foot (30 cm) to 2 feet (61 cm) apart. Be sure your cuts are perpendicular to the direction of the wood. Start on 1 side of the room and work your way systematically to the other side, spacing each cut about 1 foot (30 cm) to 2 feet (61 cm) apart.[3] Hardwood Floors
×