Tongue-and-groove: One side and one end of the plank have a groove, the other side and end have a tongue (protruding wood along an edge's center). The tongue and groove fit snugly together, thus joining or aligning the planks, and are not visible once joined. Tongue-and-groove flooring can be installed by glue-down (both engineered and solid), floating (mostly engineered only), or nail-down (not recommended for most engineered). Hardwood Floors
Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7] Hardwood Floors
A hardwood flooring installation takes time, precision, and know-how to get it right. Even for experienced DIYers, hardwood installations can be challenging. A lot depends on your ability to take the time to learn what you need to know to properly install a hardwood floor, so that it will look and perform beautifully. If you've never installed hardwood you will find it worthwhile to hire a professional installer.
Hardwood floors can last a long time, but eventually they need to be replaced. Luckily, it's a pretty straightforward process! Use a circular saw to cut the old hardwood into pieces, then remove the old flooring. Prepare your subflooring so that it's clean and perfectly level. After that, choose your replacement flooring and follow the process for installing that particular type of hardwood! Denver Hardwood Flooring
Not only is bamboo resistant to moisture, but it is environmentally friendly and an optimal choice for those who are looking to build “green.” The plant grows faster and does not take as long to re-grow than a typical hardwood tree, therefore not contributing to deforestation. Bamboo flooring is softer than traditional hardwoods, so it will not cause pain if it is stood on for long periods of time. The softness of the floor will also reduce noise.
Refinishing can actually take much more time than fully replacing a wood floor. Refinishing is a messy, meticulous process than can take approximately four to five days, during which the floor surface must remain completely untouched. The process requires sanders, edgers, buffers, scrapers, brushes, base coat sealers, topcoat sealers, putty knives and sometimes paint. Replacement, on the other hand, can be done in considerably less time using only lumber, a couple of saws, measuring tape, a flat bar, a chalk line and a nail gun.

Add style, warmth, and value to your home with beautiful hardwood floors from The Home Depot. Our hardwood floors are available in solid and engineered hardwood, and a wide variety of colors, styles and wood species. Whether you’re interested in a traditional look, like a classic oak wood floor or something more modern and contemporary, like bamboo floors or cork flooring, we have everything you need to get your flooring project done.
Another common hardwood floor malady is the development of gaps between planks. The most common causes of gaps between the boards is Mother Nature. Wood shrinks as it dries out, and it expands when it gets wet and humid. That regular expansion and contraction over time is the most common cause of gaps, and is the main reason why most gaps are seasonal in nature. Perhaps your best plan of action is to exercise patience. Denver Hardwood Floors
Tongue-and-groove: One side and one end of the plank have a groove, the other side and end have a tongue (protruding wood along an edge's center). The tongue and groove fit snugly together, thus joining or aligning the planks, and are not visible once joined. Tongue-and-groove flooring can be installed by glue-down (both engineered and solid), floating (mostly engineered only), or nail-down (not recommended for most engineered). Hardwood Floors
Make cuts perpendicular to the direction the wood is laying. Using a circular saw, make single cuts straight across the flooring that are about 1 foot (30 cm) to 2 feet (61 cm) apart. Be sure your cuts are perpendicular to the direction of the wood. Start on 1 side of the room and work your way systematically to the other side, spacing each cut about 1 foot (30 cm) to 2 feet (61 cm) apart.[3] Denver Hardwood Floors
Top quality laminate will not match the look and feel of real wood floors. The areas where the planks join will wear considerably over time, and when damage sets in, it is not an easy repair. Laminate is easily damaged by moisture, and when that damage sets in, it cannot be fixed. If the laminate is not laid correctly, it will not be appealing to potential renters or buyers. Denver Hardwood Floor Install

This durable prefinished solid real wood floor will This durable prefinished solid real wood floor will enhance the value of your home. The flooring is made of 3/4 in. thick sawn solid wood and features mother nature's naturally occurring beauty marks such as distinctive color variation knots and mineral streaks. Plank length is totally random and varies based ...  More + Product Details Close Denver Hardwood Floors
Floating installation: A floating installation is where the flooring is laid down in a glueless manner on top of a layer of underlay. The individual planks are locked together, and are not glued or nailed down to the subfloor. By doing this the floor is floating above the underlay, and can be laid on top of existing tile or marble, without the risk of damaging the subflooring. Denver Hardwood Flooring
Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store.
Oak has always been a popular choice for hardwood flooring. The color is visually appealing, looks inviting, and has many advantages. You’ll find the wood easier to clean, and it easily blends in with furniture and home interior designs you already have. Plus, oak is a good investment if you’re considering selling your house in the future, since the wood can last for many years. Denver Hardwood Floors
Solid hardwood floors are made of planks milled from a single piece of timber. Solid hardwood floors were originally used for structural purposes, being installed perpendicular to the wooden support beams of a building known as joists or bearers. With the increased use of concrete as a subfloor in some parts of the world, engineered wood flooring has gained some popularity. However, solid wood floors are still common and popular. Solid wood floors have a thicker wear surface and can be sanded and finished more times than an engineered wood floor.[2] It is not uncommon for homes in New England, Eastern Canada, USA, and Europe to have the original solid wood floor still in use today. Denver Hardwood Floors
Refinishing can actually take much more time than fully replacing a wood floor. Refinishing is a messy, meticulous process than can take approximately four to five days, during which the floor surface must remain completely untouched. The process requires sanders, edgers, buffers, scrapers, brushes, base coat sealers, topcoat sealers, putty knives and sometimes paint. Replacement, on the other hand, can be done in considerably less time using only lumber, a couple of saws, measuring tape, a flat bar, a chalk line and a nail gun. Hardwood Floors
×