Wood floors offer warmth and enhance the look of your rooms while increasing the value of your home. Wood flooring comes in a variety of styles and materials from solid hardwood to engineered hardwood to bamboo. You’ll find wooden floors also comes in a number of shades. In addition to looking great, wood floors are durable making them perfect for homes with pets and children. Denver Hardwood Floors
If your floor has noticeable scratches throughout, your best option is to sand down the floor and refinish it. A complete sanding removes scratches, but beware: This only works on real wood floors, not bamboo. If you have an engineered wood floor with a real wood surface, make sure the real wood surface is more than 1mm thick—sanding usually takes at least this much wood off the surface, so a thicker layer is required for a complete sanding. Hardwood Floors
Price is the first obvious variable to consider. It is almost always cheaper to refinish your floor than to replace it. When replacing, you must consider the cost of the new wood as well as the installation. You can offset much of this cost by installing the floor yourself, but this is a very invasive process that requires specialized knowledge and precision. You can typically refinish a wood floor yourself, with just a few inexpensive solutions. Denver Hardwood Flooring
This process begins with the same treatment process that the rotary peel method uses. However, instead of being sliced in a rotary fashion, with this technique the wood is sliced from the log in much the same manner that lumber is sawn from a log – straight through. The veneers do not go through the same manufacturing process as rotary peeled veneers. Engineered hardwood produced this way tends to have fewer problems with "face checking", and also does not have the same plywood appearance in the grain.[3] However, the planks can tend to have edge splintering and cracking because the veneers have been submerged in water and then pressed flat. Hardwood Floors

The age of your floor also plays a role. If your floor has been in place for decades, it may resist refinishing for a number of reasons. For instance, if it has already been refinished several times or if too much of the surface wood has become exposed, refinishing your floor may have little effect. For very old floors, replacement can often be preferable to refinishing. Denver Hardwood Flooring


Most floors use a tongue-and-groove design for connecting adjacent strips. This design makes replacing a single strip or plank challenging, but not impossible. First, look for any nails in the damaged board and drive them as far through the board as possible by using a hammer and nail set. Carpenters use nail sets to drive nails flush with trim without damaging the trim with a hammer. After you’ve cleared the nails, it’s time to remove the damaged board and install a new one. Follow these steps: Denver Hardwood Flooring
Width & Length – Plank flooring comes in a variety of widths and lengths. The most common widths are currently in the 5” – 6” range, but wider widths are rapidly becoming more popular. The length of your floor is also important to consider depending on the size of your space. Hardwood flooring comes in mixed lengths because imperfections are cut out of longer planks during production. Rigid Core flooring is built to size and comes in lengths ranging from 36” up to 80+”.

Over the years, many hardwood floors develop small splits or cracks in the surface of the wood. These can be spot repaired with some angled nails to secure the two pieces together, along with some wood putty to hide the blemishes. If your floor is suffering from large cracks, however, you might want to think about refinishing the floor. And if the split is particularly bad, you should probably replace the damaged plank altogether. Denver Hardwood Floors


Some benefits of wood flooring include ease of cleaning, durability, and style variety. Wood floors are much easier to keep clean than carpet and pet hair or dander is quick to remove. They are very durable and with proper care, they will look great for years to come. Plus, wood flooring is available in a multitude of styles and colors guaranteeing there is a look out there for a classic or contemporary home. Denver Hardwood Flooring
Awesome explanation! When I say heat pump to people, it's amazing how often their eyes glaze over...even though most of them have had refrigerators and air-conditioners their whole lives and have never asked themselves how they work. Same principle! Compressor and expansion valve (and the heat-holding capacity of a phase change; another confusing one for people). thanks for helping educate! Denver Hardwood Floors
Durable and available in a variety of colors, hardwood flooring is a classic option for any home. Installation prices vary depending on the type of wood you choose. Depending upon your selections, the total cost for hardwood floor installation, including labor and materials, can average up to $6 to $8 per square foot. Keep reading to learn more about hardwood floor installation costs. Denver Hardwood Floors

A hardwood flooring installation takes time, precision, and know-how to get it right. Even for experienced DIYers, hardwood installations can be challenging. A lot depends on your ability to take the time to learn what you need to know to properly install a hardwood floor, so that it will look and perform beautifully. If you've never installed hardwood you will find it worthwhile to hire a professional installer. Denver Hardwood Floors
The age of your floor also plays a role. If your floor has been in place for decades, it may resist refinishing for a number of reasons. For instance, if it has already been refinished several times or if too much of the surface wood has become exposed, refinishing your floor may have little effect. For very old floors, replacement can often be preferable to refinishing. Denver Hardwood Flooring
Hardwood can match any décor, from traditional light wood floors to trendy white wood flooring, grey wood floors and dark wood floors. Start with unfinished hard wood flooring boards to create a blank canvas for stain and unique design. We also have hand-scraped hardwood and distressed wood flooring to add a rustic, timeworn look. A wide plank wood flooring can also make a room feel bigger and more modern. Hardwood flooring also has DIY installation that’s easy with tongue and groove flooring options.

As the name suggests, solid hardwood is a single, solid piece of wood. Its natural simplicity has made it a popular flooring choice for generations, but that same simplicity makes it less than ideal for modern homes. Wood is a naturally porous material, meaning it is soft, extremely prone to denting, and absorbs water like a sponge. All of these attributes are ideal for helping trees grow, but they don’t translate well to modern flooring. Floors today need to withstand heavy traffic, drops, scratches, and most importantly, spills. Denver Hardwood Floor Install

It is difficult to compare solid wood flooring to engineered wood flooring due to the wide range of quality in both product categories, particularly engineered. Solid wood has some limitations. Recommended maximum widths and lengths are typically 5" / 127mm wide and 7' / 2100mm long. Solid hardwood is also more prone to "gapping" (excessive space between planks), "crowning" (convex curving upwards when humidity increases) and "cupping" (a concave or "dished" appearance of the plank, with the height of the plank along its longer edges being higher than the centre) with increased plank size. Solid wood cannot be used with underfloor radiant heating.[5] However extra care is necessary with the planning and installation of the heating system and the wood flooring, such as limiting the temperature to 85 °F (29 °C), avoid sharp temperature fluctuations, utilizing an outdoor thermostat to anticipate heating demands, and monitoring the moisture content for the subfloor before installation. Denver Hardwood Floor Install


Choosing teak for your hardwood floors can be a smart choice. You’ll find teak is resistant to pests, as the natural oils found in the wood are undesirable to most insects, including termites. Teak is also a water-resistant wood choice, a bonus if you have young, active children or pets that come indoors soaking wet after walks in the rain. Teak bears an attractive reddish-brown color. However, if left untreated, teak can turn a silver color if exposed to UV rays of sunlight. To prevent discoloration and wear, you can treat the wood with a coating of oil to seal it so that you can enjoy beautiful teak floors for years to come. Denver Hardwood Floor Install
Because tongue-and-groove boards are locked in place, removal involves cutting out the middle of each damaged board. The easiest way is to bore a 1-in.-dia. hole through both ends of each damaged board (photo 1). Then use a circular saw to connect the two holes (photo 2). Follow these steps to safely make the plunge cuts you need to repair your hardwood floors: 1. Adjust the depth of cut to the thickness of the floorboards. Plug in the saw and put on eye protection. 2. Pull back the retractable blade guard with your thumb. Then hold the nose of the baseplate on the floorboard and lift up the rear of the saw. 3. Align the blade with the right edge of one of the holes. Make sure the blade isn't touching the floor, then squeeze the trigger and slowly lower the spinning blade into the board. 4. Grip the saw firmly with both hands and guide it in a straight line until you cut into the right edge of the hole at the opposite end of the board. 5. Move back to the first hole, align the blade with the left edge and cut to the left edge of the second hole. Pry out the middle section with a hammer and chisel. Chop out the remaining edges, being careful not to damage any surrounding boards (photo 3). The "tongue" piece will be nailed in place, so break it out in small pieces. Then pull out the nails with a hammer or locking pliers. The existing floorboards have a tongue and groove milled on each end and along the edges. Chop off the tongue exposed by the board you just removed so you can slip in the new board (photo 4). Denver Hardwood Floors
Most floors use a tongue-and-groove design for connecting adjacent strips. This design makes replacing a single strip or plank challenging, but not impossible. First, look for any nails in the damaged board and drive them as far through the board as possible by using a hammer and nail set. Carpenters use nail sets to drive nails flush with trim without damaging the trim with a hammer. After you’ve cleared the nails, it’s time to remove the damaged board and install a new one. Follow these steps:

Sanding provides a method for smoothing an installed floor, compensating for unevenness of the subfloor. Additionally, sanding is used to renew the appearance of older floors. Sanding using successively finer grades of sandpaper is required to ensure even stain penetration when stains are used, as well as to eliminate visible scratches from coarser sandpaper grades used initially. Prior to modern polyurethanes, oils and waxes were used in addition to stains to provide finishes.[7] Beeswax and linseed oil, for example, are both natural crosslinking polymers and harden over time.[8]
Solid hardwood floors are made of planks milled from a single piece of timber. Solid hardwood floors were originally used for structural purposes, being installed perpendicular to the wooden support beams of a building known as joists or bearers. With the increased use of concrete as a subfloor in some parts of the world, engineered wood flooring has gained some popularity. However, solid wood floors are still common and popular. Solid wood floors have a thicker wear surface and can be sanded and finished more times than an engineered wood floor.[2] It is not uncommon for homes in New England, Eastern Canada, USA, and Europe to have the original solid wood floor still in use today. Denver Hardwood Floor Install
Tongue-and-groove: One side and one end of the plank have a groove, the other side and end have a tongue (protruding wood along an edge's center). The tongue and groove fit snugly together, thus joining or aligning the planks, and are not visible once joined. Tongue-and-groove flooring can be installed by glue-down (both engineered and solid), floating (mostly engineered only), or nail-down (not recommended for most engineered).
Price is the first obvious variable to consider. It is almost always cheaper to refinish your floor than to replace it. When replacing, you must consider the cost of the new wood as well as the installation. You can offset much of this cost by installing the floor yourself, but this is a very invasive process that requires specialized knowledge and precision. You can typically refinish a wood floor yourself, with just a few inexpensive solutions. Denver Hardwood Floor Install
Most floors use a tongue-and-groove design for connecting adjacent strips. This design makes replacing a single strip or plank challenging, but not impossible. First, look for any nails in the damaged board and drive them as far through the board as possible by using a hammer and nail set. Carpenters use nail sets to drive nails flush with trim without damaging the trim with a hammer. After you’ve cleared the nails, it’s time to remove the damaged board and install a new one. Follow these steps: Denver Hardwood Floors
Glue down engineered hardwood, alternatively. If you don't want to nail down the boards, you do have the option of using adhesive to put engineered hardwood in place. It's a good choice, but won't last as long or be as sturdy as nailed down hardwood. The procedure is very similar to the nail-down process. Follow the adhesive manufacturer's instructions for installation and drying times.[11] Denver Hardwood Floor Install
Width & Length – Plank flooring comes in a variety of widths and lengths. The most common widths are currently in the 5” – 6” range, but wider widths are rapidly becoming more popular. The length of your floor is also important to consider depending on the size of your space. Hardwood flooring comes in mixed lengths because imperfections are cut out of longer planks during production. Rigid Core flooring is built to size and comes in lengths ranging from 36” up to 80+”. Denver Hardwood Floors
Oak has always been a popular choice for hardwood flooring. The color is visually appealing, looks inviting, and has many advantages. You’ll find the wood easier to clean, and it easily blends in with furniture and home interior designs you already have. Plus, oak is a good investment if you’re considering selling your house in the future, since the wood can last for many years.

No matter what type of hardwood flooring you choose, proper care and maintenance will help them look beautiful even longer. First off, don’t let the dirt and dust collect. At least once a week, you’ll want to go over your hardwood floors with a broom or dust mop to pick up any dirt, dust, hair or pet dander. If you’re using a vacuum, make sure it’s set to ‘wood floors’ so that you’re not beating up your floors and damaging them in the process. Hardwood Floors
×