Refinish, refinish, refinish! In almost every case it is preferable to refinish rather than replace hardwood floors. Part of the appeal of hardwood is that it lasts so long. A quality hardwood floor can be sanded down and refinished at least six times, and up to ten times before you need to replace it. You can change the color, closely match and replace warped, stained, or termite ingested planks, silence squeaky boards, and fill gaps or patch knots. With all of these easy solutions, why would anyone choose to replace hardwood floors? Well, here are the cases when a complete rehaul becomes a better option. Hardwood Floors
Cut a new length of flooring to fit snugly into the space of the old board. It doesn't matter what kind of saw you use to repair your hardwood floors; just make sure the cuts are perfectly square. After trimming the board to length, turn it upside down and use a chisel to chop off the lower lip of the grooved edge (photo 5). That allows it to fit over the protruding tongue of the adjacent floorboard. Test-fit the new piece. If it's slightly lower than the surrounding floorboards, shim it up with strips of kraft paper. Then remove the board and spread carpenter's glue on the tongues and grooves of the new and old pieces. Slip the new board into place (photo 6), protect it with a scrap-wood block and tap it down with a hammer. Cover the board with wax paper, then hold it down overnight with heavy books or weights. An alternative to gluing: Simply face-nail the board with 6d finishing nails. Bore pilot holes at a slight angle, then drive in the nails. Tap them below the surface with a nailset (photo 7) and fill the holes with wood putty. Lightly sand the entire board smooth, but be careful not to remove too much finish from surrounding boards. After finding a matching stain color by experimenting on scraps of flooring, stain the boards to match the original floor. Let dry overnight, then apply two coats of clear polyurethane varnish. If the old floor is unstained, just apply the polyurethane. Hardwood Floors
Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7] Denver Hardwood Flooring
Top quality laminate will not match the look and feel of real wood floors. The areas where the planks join will wear considerably over time, and when damage sets in, it is not an easy repair. Laminate is easily damaged by moisture, and when that damage sets in, it cannot be fixed. If the laminate is not laid correctly, it will not be appealing to potential renters or buyers. Denver Hardwood Floor Install
While the overall thickness of flooring is going to vary by category, it is still important to know what is contributing to that thickness. Engineered wood flooring can inflate thickness by adding more layers of plywood or particle board, but still only offer a thin veneer of real wood on top. The dense core allows for Rigid Core floors to be significantly thinner than traditional hardwood floors, with WPC floors being thicker than SPC products. That doesn’t mean all Rigid Core floors are made equally though. Just like how engineered hardwood flooring can inflate thickness, Rigid Core flooring can alter the overall thickness by increasing the size of the acoustical padding on the back. While this padding adds a lot of great features, it doesn’t need to be any thicker than 1mm in size. When it comes to Rigid Core flooring, the thickness of the core is most important.

If you have a small, single scratch that’s only noticeable when you get close (like a scratch caused by an excited pet) and your floor has a relatively new finish, try a DIY home solution first. Mix equal parts apple cider vinegar and olive oil in a small cup, and dab the mixture into the scratch. Leave it for the rest of the day, and rub it out. This method often takes care of minor scratches. Hardwood Floors
We had bought and installed this beautiful product in our downstairs a few years ago. It's now time to do the upstairs and the product was the same excellent value for the price. Arrived quicker than we needed, but gives it time to acclimate to our home. We will be using the same installer and he was happy we are ordering the same product from the same company. He was VERY impressed by the quality of the product last time. I'm excited to see the completed project as I love this wood on our main floor. Denver Hardwood Flooring
Lowe’s has what you need to bring value-adding beauty to your home with hardwood flooring. There are plenty of species to choose from, including acacia wood flooring, walnut flooring, maple flooring, hickory hardwood flooring and cherry wood flooring. Depending on your budget and room’s traffic level, you’ll be sure to find a style to suit your needs. Denver Hardwood Flooring
Once you discover the differences among the popular hardwood flooring species, you’ll look forward to starting your own renovation. If you like to entertain at home and invite guests over often, consider maple’s strong qualities. If you have children or dogs who often bring water into the house, teak and its water-resistant properties can be a great option for you. For a longer-lasting wood that blends in well with almost all types of décor, try oak for your choice of hardwood.
Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store. Denver Hardwood Flooring
Glue down engineered hardwood, alternatively. If you don't want to nail down the boards, you do have the option of using adhesive to put engineered hardwood in place. It's a good choice, but won't last as long or be as sturdy as nailed down hardwood. The procedure is very similar to the nail-down process. Follow the adhesive manufacturer's instructions for installation and drying times.[11] Hardwood Floors
Not only is bamboo resistant to moisture, but it is environmentally friendly and an optimal choice for those who are looking to build “green.” The plant grows faster and does not take as long to re-grow than a typical hardwood tree, therefore not contributing to deforestation. Bamboo flooring is softer than traditional hardwoods, so it will not cause pain if it is stood on for long periods of time. The softness of the floor will also reduce noise. Denver Hardwood Floors
The Home Depot offers a stunning selection of solid wood and engineered flooring that is sustainably sourced to help preserve our world’s endangered forests. Installation services are available for homes of all sizes. Licensed, certified, and vetted with background checks, our professional installers show up wearing an official Home Depot badge, so you’ll know we sent them. We are transparent about our products, so you know exactly what’s being installed in your home. To help you create your dream home sooner, The Home Depot also offers financial assistance options like project loans and specialty credit cards.
Maple is another great choice for hardwood flooring. Many people prefer its light tan look, which blends into home interior spaces. As one of the strongest woods, maple is a top choice for high-traffic areas of a home. The wood doesn’t scuff easily, making it a good choice for homes with children or those with a lot of foot traffic across the floors. Maple requires minimal maintenance, with weekly sweeping and annual applications of wood soap to prolong the life of the floors. Denver Hardwood Floor Install
Over the years, many hardwood floors develop small splits or cracks in the surface of the wood. These can be spot repaired with some angled nails to secure the two pieces together, along with some wood putty to hide the blemishes. If your floor is suffering from large cracks, however, you might want to think about refinishing the floor. And if the split is particularly bad, you should probably replace the damaged plank altogether.
To fix a buckled floorboard, you need to be able to access the floor from below. The way to tackle this problem is to put weight on the buckled area from above — a cement block works well. Then install a 1 1/4-inch screw in the buckled flooring from below. Allow the screw to penetrate only halfway into the flooring, or it may come up through the finished surface. Driving the screw through the subfloor and into the flooring pulls the flooring down against the subfloor and gets rid of the buckled spot.
If your floors are in need of a deeper cleaning, use a wood floor cleaner. Follow the instructions for diluting the cleaner in water. Clean the floors with a damp mop, going with the grain. Then, go back over the floor with a clean, damp mop to remove any excess cleaner. Finish by drying the floor completely with a dry towel. Remember, leftover standing water could damage your wood floors.
Cupped floors, also called washboarding, develops gradually across the width of the wood strip where the edges of the hardwood planks raise up and the center of the board sinks down. The cause of cupped floors is a moisture imbalance where there is more water on the bottom side of the wood plank than on the top. The only cure is to balance the humidity levels in your home, and to give the surface time to return back to normal. After the floor has stabilized, you can have a professional sand it flat and re-finish it to perfection. Hardwood Floors
Maple is another great choice for hardwood flooring. Many people prefer its light tan look, which blends into home interior spaces. As one of the strongest woods, maple is a top choice for high-traffic areas of a home. The wood doesn’t scuff easily, making it a good choice for homes with children or those with a lot of foot traffic across the floors. Maple requires minimal maintenance, with weekly sweeping and annual applications of wood soap to prolong the life of the floors. Denver Hardwood Floor Install
Installing a hardwood floor yourself can save you money – if you know what you’re doing. Improper preparation and installation can lead to warping and buckling, which will ruin flooring that would otherwise remain beautiful for years to come. The most important thing you can do to ensure the structural integrity of your floor is to properly prepare for the installation process. Here are various articles to help you!

A number of proprietary features for solid wood floors are available. Many solid woods come with grooves cut into the back of the wood that run the length of each plank, often called 'absorption strips,' that are intended to reduce cupping. Solid wood floors are mostly manufactured 0.75 inches (19 mm) thick with a tongue-and-groove for installation.


Enhance your home with beautiful hardwood flooring that Enhance your home with beautiful hardwood flooring that fits your budget. Full of abundant character and color variation the Bruce Plano collection celebrates the beauty of natural hardwood. Enjoy natural features including mineral streaks knots and small holes and minor milling imperfections. Design your floor to your unique tastes with ...  More + Product Details Close Hardwood Floors
Glue down engineered hardwood, alternatively. If you don't want to nail down the boards, you do have the option of using adhesive to put engineered hardwood in place. It's a good choice, but won't last as long or be as sturdy as nailed down hardwood. The procedure is very similar to the nail-down process. Follow the adhesive manufacturer's instructions for installation and drying times.[11] Denver Hardwood Flooring
Make cuts perpendicular to the direction the wood is laying. Using a circular saw, make single cuts straight across the flooring that are about 1 foot (30 cm) to 2 feet (61 cm) apart. Be sure your cuts are perpendicular to the direction of the wood. Start on 1 side of the room and work your way systematically to the other side, spacing each cut about 1 foot (30 cm) to 2 feet (61 cm) apart.[3] Hardwood Floors
×