Most floors use a tongue-and-groove design for connecting adjacent strips. This design makes replacing a single strip or plank challenging, but not impossible. First, look for any nails in the damaged board and drive them as far through the board as possible by using a hammer and nail set. Carpenters use nail sets to drive nails flush with trim without damaging the trim with a hammer. After you’ve cleared the nails, it’s time to remove the damaged board and install a new one. Follow these steps: Denver Hardwood Flooring
Solid hardwood is great for high traffic areas and rooms on the first or second floors where there’s limited moisture. You can purchase your solid hardwood floors either prefinished or unfinished. Prefinished hardwood floors have a coating that protects them and they’re ready to install right out of the box. Unfinished hardwoods allow you to apply your own stain color. Denver Hardwood Flooring
Make cuts perpendicular to the direction the wood is laying. Using a circular saw, make single cuts straight across the flooring that are about 1 foot (30 cm) to 2 feet (61 cm) apart. Be sure your cuts are perpendicular to the direction of the wood. Start on 1 side of the room and work your way systematically to the other side, spacing each cut about 1 foot (30 cm) to 2 feet (61 cm) apart.[3]
Lowe’s has what you need to bring value-adding beauty to your home with hardwood flooring. There are plenty of species to choose from, including acacia wood flooring, walnut flooring, maple flooring, hickory hardwood flooring and cherry wood flooring. Depending on your budget and room’s traffic level, you’ll be sure to find a style to suit your needs.
 116% harder than Red Oak (1)  12% harder than Red Oak (11)  123% Harder than Red Oak (4)  125% harder than Red Oak (2)  141% harder than Red Oak (2)  15% softer than Red Oak (2)  165% harder than Red Oak (2)  174% harder than Red Oak (5)  18% softer than Red Oak (1)  185% harder than Red Oak (4)  198 % harder than Red Oak (2)  2% harder than Red Oak (2)  2% Softer than Red Oak (1)  25% softer than Red Oak (1)  28% harder than Red Oak (1)  30% harder than Red Oak (8)  33% harder than Red Oak (2)  41% harder than Red Oak (7)  43% harder than Red Oak (1)  5% harder than Red Oak (8)  53% softer than Red Oak (1)  6% harder than Red Oak (14)  67% harder than Red Oak (5)  74% harder than Red Oak (2)  81% harder than Red Oak (2)  82% harder than Red Oak (2)  9% softer than Red Oak (1)  about the same as Red Oak (7)  Benchmark at 1290 on Janka Scale (37)
A buckled floor happens when the boards warp and lift up from the subfloor that they are attached to. You’ll most likely need to call in a hardwood floor installer to identify the root of the problem if buckling is an issue. Once the cause of your buckling has been identified, you’ll need to take the necessary measures to ensure that your hardwood planks are firmly attached to the subfloor so that the problem no longer persists.
Glue down engineered hardwood, alternatively. If you don't want to nail down the boards, you do have the option of using adhesive to put engineered hardwood in place. It's a good choice, but won't last as long or be as sturdy as nailed down hardwood. The procedure is very similar to the nail-down process. Follow the adhesive manufacturer's instructions for installation and drying times.[11] Denver Hardwood Floor Install

 Acacia (9)  American Walnut (1)  Ash (5)  Bamboo (22)  Beech (5)  Birch (3)  Bloodwood (2)  Brazilian Cherry (10)  Brazilian Chestnut (5)  Brazilian Koa (9)  Brazilian Oak (5)  Brazilian Walnut (5)  Cumaru (3)  Curupay (2)  Hevea (4)  Hickory (27)  Maple (14)  Oak (15)  Pecan (3)  Pine (10)  Purple Heart (2)  Red Cumaru (2)  Red Maple (1)  Red Oak (40)  Short Leaf Acacia (3)  ShortLeaf Acacia (1)  Spanish Hickory (3)  Tamboril (2)  Tauari (3)  Walnut (1)  White Oak (34) Denver Hardwood Floor Install

Most floors use a tongue-and-groove design for connecting adjacent strips. This design makes replacing a single strip or plank challenging, but not impossible. First, look for any nails in the damaged board and drive them as far through the board as possible by using a hammer and nail set. Carpenters use nail sets to drive nails flush with trim without damaging the trim with a hammer. After you’ve cleared the nails, it’s time to remove the damaged board and install a new one. Follow these steps: Denver Hardwood Floor Install
Warped hardwood floors, also known as sagging, is a serious problem for any homeowner. It is often the result of serious moisture problems, and any evidence of warped hardwood floors needs to be addressed immediately. Warped hardwood floors are rarely the result of faulty hardwood or installation, but are a symptom of larger moisture problems in the home itself that need to be taken care of. Hardwood Floors
It’s important to start by knowing what kind of finish is on your floor. Is your finish oil or water based? Do you have a wax coating? Is the wood varnished or stained? Is there an aluminum oxide coating? Know what the surface is made of so you know how to start your wood floor scratch repair. If you didn’t install the floor and aren’t sure what type of finish it has, you can check here for more details on identifying it. Denver Hardwood Flooring
It is difficult to compare solid wood flooring to engineered wood flooring due to the wide range of quality in both product categories, particularly engineered. Solid wood has some limitations. Recommended maximum widths and lengths are typically 5" / 127mm wide and 7' / 2100mm long. Solid hardwood is also more prone to "gapping" (excessive space between planks), "crowning" (convex curving upwards when humidity increases) and "cupping" (a concave or "dished" appearance of the plank, with the height of the plank along its longer edges being higher than the centre) with increased plank size. Solid wood cannot be used with underfloor radiant heating.[5] However extra care is necessary with the planning and installation of the heating system and the wood flooring, such as limiting the temperature to 85 °F (29 °C), avoid sharp temperature fluctuations, utilizing an outdoor thermostat to anticipate heating demands, and monitoring the moisture content for the subfloor before installation. Denver Hardwood Flooring
Some benefits of wood flooring include ease of cleaning, durability, and style variety. Wood floors are much easier to keep clean than carpet and pet hair or dander is quick to remove. They are very durable and with proper care, they will look great for years to come. Plus, wood flooring is available in a multitude of styles and colors guaranteeing there is a look out there for a classic or contemporary home. Denver Hardwood Flooring
The Home Depot offers a stunning selection of solid wood and engineered flooring that is sustainably sourced to help preserve our world’s endangered forests. Installation services are available for homes of all sizes. Licensed, certified, and vetted with background checks, our professional installers show up wearing an official Home Depot badge, so you’ll know we sent them. We are transparent about our products, so you know exactly what’s being installed in your home. To help you create your dream home sooner, The Home Depot also offers financial assistance options like project loans and specialty credit cards. Hardwood Floors
We had bought and installed this beautiful product in our downstairs a few years ago. It's now time to do the upstairs and the product was the same excellent value for the price. Arrived quicker than we needed, but gives it time to acclimate to our home. We will be using the same installer and he was happy we are ordering the same product from the same company. He was VERY impressed by the quality of the product last time. I'm excited to see the completed project as I love this wood on our main floor. Hardwood Floors
Hardwood species used in flooring are given a hardwood hardness rating, which indicates how resistant the wood is to dents and wear. This rating is based off a test called the Janka Hardness Test, and it measures the force needed to press a steel ball into the wood sample. The highest possible score on this test is a little over 5,000, with most traditional solid wood floors scoring in the 1,000-2,000 range. The superior density of Rigid Core flooring would exceed the limitations of the Janka test, and instead a higher impact testing is needed to measure real world performance. Here is how the general hardness of plank flooring ranks: Denver Hardwood Floor Install
Oak has always been a popular choice for hardwood flooring. The color is visually appealing, looks inviting, and has many advantages. You’ll find the wood easier to clean, and it easily blends in with furniture and home interior designs you already have. Plus, oak is a good investment if you’re considering selling your house in the future, since the wood can last for many years.
A number of proprietary features for solid wood floors are available. Many solid woods come with grooves cut into the back of the wood that run the length of each plank, often called 'absorption strips,' that are intended to reduce cupping. Solid wood floors are mostly manufactured 0.75 inches (19 mm) thick with a tongue-and-groove for installation. Hardwood Floors
Make cuts perpendicular to the direction the wood is laying. Using a circular saw, make single cuts straight across the flooring that are about 1 foot (30 cm) to 2 feet (61 cm) apart. Be sure your cuts are perpendicular to the direction of the wood. Start on 1 side of the room and work your way systematically to the other side, spacing each cut about 1 foot (30 cm) to 2 feet (61 cm) apart.[3] Denver Hardwood Floors

Before you choose a hardwood floor, think about how much foot traffic you expect. Consider the look you want and how much you plan to invest. And, if you’re still undecided, browse our selection of other flooring options, including vinyl flooring, tile, parquet, and laminate flooring. You can also find helpful information in our cost guide. From selection to delivery and installation, the Home Depot is your one-stop shop for all your flooring needs. Denver Hardwood Flooring
Enhance your home with beautiful hardwood flooring that Enhance your home with beautiful hardwood flooring that fits your budget. Full of abundant character and color variation Bruce Plano Gunstock Oak celebrates the beauty of natural hardwood. Enjoy natural features including mineral streaks knots and small holes and minor milling imperfections. Design your floor to your unique tastes with ...  More + Product Details Close
Add style, warmth, and value to your home with beautiful hardwood floors from The Home Depot. Our hardwood floors are available in solid and engineered hardwood, and a wide variety of colors, styles and wood species. Whether you’re interested in a traditional look, like a classic oak wood floor or something more modern and contemporary, like bamboo floors or cork flooring, we have everything you need to get your flooring project done. Denver Hardwood Floor Install
Refinishing a floor takes a lot of time. You’ll need to remove all of the furniture from the room. The wood needs to be sanded bare. If you need to make a structural or cosmetic repair, you must do so before staining and coating. During the week that all of this is going on, nothing else can happen in that room. Dogs cannot walk through and sniff everything, children cannot bounce their balls, dust is everywhere, and the smell is enough to kill you. Well not really, but you get the idea. All of this time and trouble is reason enough for some homeowners to prefer having the old floor ripped out to put in something fresh and new. Hardwood Floors
Awesome explanation! When I say heat pump to people, it's amazing how often their eyes glaze over...even though most of them have had refrigerators and air-conditioners their whole lives and have never asked themselves how they work. Same principle! Compressor and expansion valve (and the heat-holding capacity of a phase change; another confusing one for people). thanks for helping educate! Hardwood Floors
Wood flooring is any product manufactured from timber that is designed for use as flooring, either structural or aesthetic. Wood is a common choice as a flooring material and can come in various styles, colors, cuts, and species. Bamboo flooring is often considered a form of wood flooring, although it is made from a grass (bamboo) rather than a timber.[1]
The natural process of things will tend to close gaps as the weather and humidity changes. As a rule, if the gap is less than the thickness of a dime, your flooring is normal and there’s nothing to worry about. If your gaps are more persistent, you might need to call in a professional to tighten up your hardwood floor so that they cease to be a problem. Denver Hardwood Floors

Before you choose a hardwood floor, think about how much foot traffic you expect. Consider the look you want and how much you plan to invest. And, if you’re still undecided, browse our selection of other flooring options, including vinyl flooring, tile, parquet, and laminate flooring. You can also find helpful information in our cost guide. From selection to delivery and installation, the Home Depot is your one-stop shop for all your flooring needs. Denver Hardwood Floors
Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7] Denver Hardwood Floor Install
Menards® has everything you need to cover your floors in style! We offer a wide selection of hardwood flooring options that are fit to use in any room of your home. Some of our quality hardwood floorcoverings include engineered hardwood, which is built to last and has higher resistance to moisture levels. We also carry a variety of solid hardwood flooring to give your home traditional character and style. If you are interested in another durable flooring option for your home, we have cork flooring. In addition to strong and durable flooring, we offer everything you will need for installation and maintenance as well as hardwood moulding and trims to help you finish the job. Once the flooring installation is complete, keep them looking clean with our selection of vacuum cleaners and floor care products. Next, complete the look with area rugs, mats, and runners to enhance your home's décor and add coziness to the space. Denver Hardwood Floor Install
Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store.
If your floors are in need of a deeper cleaning, use a wood floor cleaner. Follow the instructions for diluting the cleaner in water. Clean the floors with a damp mop, going with the grain. Then, go back over the floor with a clean, damp mop to remove any excess cleaner. Finish by drying the floor completely with a dry towel. Remember, leftover standing water could damage your wood floors. Denver Hardwood Flooring
Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7]
 Bamboo Flooring (22)  BELLAWOOD (49)  BELLAWOOD Artisan Distressed (13)  BELLAWOOD Artisan Distressed Engineered (4)  BELLAWOOD Engineered (16)  Builders Pride (26)  Builder's Pride (10)  Builder's Pride Engineered (1)  Clover Lea (9)  Major Brand (5)  Mayflower (12)  Mayflower Engineered (19)  R.L. Colston (40)  Virginia Mill Works (8)  Virginia Mill Works Engineered (21) Denver Hardwood Floor Install
Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7]
Another common hardwood floor malady is the development of gaps between planks. The most common causes of gaps between the boards is Mother Nature. Wood shrinks as it dries out, and it expands when it gets wet and humid. That regular expansion and contraction over time is the most common cause of gaps, and is the main reason why most gaps are seasonal in nature. Perhaps your best plan of action is to exercise patience.
Regardless of the floor, the protective finish will play a large role in how scratch and stain resistant it is. Both hardwood and Rigid Core flooring are available with various types of protective finishes. Rigid Core flooring goes a step beyond hardwood though, and also has a transparent solid wear layer that protects against gouging and deeper scratches. Denver Hardwood Floors
Solid hardwood floor planks are made from a piece of wood and made to be anywhere from 18 to 20 mm thick. The boards are made with a tongue and groove to fit together for installation. Depending on the species of wood, certain floors will be harder than others. The harder the floor, the less susceptible it is to dings and scratches. The floor can be sanded and refinished several times to restore its beauty, with the total number of times being determined by the depth of the tongue from the top of the plank. Denver Hardwood Floors

Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store. Denver Hardwood Flooring
Awesome explanation! When I say heat pump to people, it's amazing how often their eyes glaze over...even though most of them have had refrigerators and air-conditioners their whole lives and have never asked themselves how they work. Same principle! Compressor and expansion valve (and the heat-holding capacity of a phase change; another confusing one for people). thanks for helping educate! Denver Hardwood Floors
Not only is bamboo resistant to moisture, but it is environmentally friendly and an optimal choice for those who are looking to build “green.” The plant grows faster and does not take as long to re-grow than a typical hardwood tree, therefore not contributing to deforestation. Bamboo flooring is softer than traditional hardwoods, so it will not cause pain if it is stood on for long periods of time. The softness of the floor will also reduce noise. Denver Hardwood Floors

Another common hardwood floor malady is the development of gaps between planks. The most common causes of gaps between the boards is Mother Nature. Wood shrinks as it dries out, and it expands when it gets wet and humid. That regular expansion and contraction over time is the most common cause of gaps, and is the main reason why most gaps are seasonal in nature. Perhaps your best plan of action is to exercise patience. Denver Hardwood Floor Install


Refinish, refinish, refinish! In almost every case it is preferable to refinish rather than replace hardwood floors. Part of the appeal of hardwood is that it lasts so long. A quality hardwood floor can be sanded down and refinished at least six times, and up to ten times before you need to replace it. You can change the color, closely match and replace warped, stained, or termite ingested planks, silence squeaky boards, and fill gaps or patch knots. With all of these easy solutions, why would anyone choose to replace hardwood floors? Well, here are the cases when a complete rehaul becomes a better option. Denver Hardwood Flooring

Sand off any paint or adhesive on the subfloor (if necessary). How pristine your subfloor needs to be depends on what kind of replacement flooring you're installing. If you plan to glue your new hardwood flooring down, sand away any paint or adhesive stuck to the subfloor with an electric sander. If you're installing nail-down, floating, or locking hardwood, you don't need to sand the subfloor.[5]


Cupped floors, also called washboarding, develops gradually across the width of the wood strip where the edges of the hardwood planks raise up and the center of the board sinks down. The cause of cupped floors is a moisture imbalance where there is more water on the bottom side of the wood plank than on the top. The only cure is to balance the humidity levels in your home, and to give the surface time to return back to normal. After the floor has stabilized, you can have a professional sand it flat and re-finish it to perfection.
Hardwood species used in flooring are given a hardwood hardness rating, which indicates how resistant the wood is to dents and wear. This rating is based off a test called the Janka Hardness Test, and it measures the force needed to press a steel ball into the wood sample. The highest possible score on this test is a little over 5,000, with most traditional solid wood floors scoring in the 1,000-2,000 range. The superior density of Rigid Core flooring would exceed the limitations of the Janka test, and instead a higher impact testing is needed to measure real world performance. Here is how the general hardness of plank flooring ranks:

Floating installation: A floating installation is where the flooring is laid down in a glueless manner on top of a layer of underlay. The individual planks are locked together, and are not glued or nailed down to the subfloor. By doing this the floor is floating above the underlay, and can be laid on top of existing tile or marble, without the risk of damaging the subflooring. Denver Hardwood Flooring
 Acacia (9)  American Walnut (1)  Ash (5)  Bamboo (22)  Beech (5)  Birch (3)  Bloodwood (2)  Brazilian Cherry (10)  Brazilian Chestnut (5)  Brazilian Koa (9)  Brazilian Oak (5)  Brazilian Walnut (5)  Cumaru (3)  Curupay (2)  Hevea (4)  Hickory (27)  Maple (14)  Oak (15)  Pecan (3)  Pine (10)  Purple Heart (2)  Red Cumaru (2)  Red Maple (1)  Red Oak (40)  Short Leaf Acacia (3)  ShortLeaf Acacia (1)  Spanish Hickory (3)  Tamboril (2)  Tauari (3)  Walnut (1)  White Oak (34) Denver Hardwood Floors
Make cuts perpendicular to the direction the wood is laying. Using a circular saw, make single cuts straight across the flooring that are about 1 foot (30 cm) to 2 feet (61 cm) apart. Be sure your cuts are perpendicular to the direction of the wood. Start on 1 side of the room and work your way systematically to the other side, spacing each cut about 1 foot (30 cm) to 2 feet (61 cm) apart.[3] Denver Hardwood Flooring
The age of your floor also plays a role. If your floor has been in place for decades, it may resist refinishing for a number of reasons. For instance, if it has already been refinished several times or if too much of the surface wood has become exposed, refinishing your floor may have little effect. For very old floors, replacement can often be preferable to refinishing. Denver Hardwood Flooring
You may be on the fence about your decision to refinish your hardwood floors because you wonder if your floors are a candidate for refinishing. The truth is, not all hardwood floors can be refinished. Although most common problems can be addressed and fixed without replacing the entire floor, there are some exceptions. Consider the following to make an informed decision. Denver Hardwood Flooring
Cut a new length of flooring to fit snugly into the space of the old board. It doesn't matter what kind of saw you use to repair your hardwood floors; just make sure the cuts are perfectly square. After trimming the board to length, turn it upside down and use a chisel to chop off the lower lip of the grooved edge (photo 5). That allows it to fit over the protruding tongue of the adjacent floorboard. Test-fit the new piece. If it's slightly lower than the surrounding floorboards, shim it up with strips of kraft paper. Then remove the board and spread carpenter's glue on the tongues and grooves of the new and old pieces. Slip the new board into place (photo 6), protect it with a scrap-wood block and tap it down with a hammer. Cover the board with wax paper, then hold it down overnight with heavy books or weights. An alternative to gluing: Simply face-nail the board with 6d finishing nails. Bore pilot holes at a slight angle, then drive in the nails. Tap them below the surface with a nailset (photo 7) and fill the holes with wood putty. Lightly sand the entire board smooth, but be careful not to remove too much finish from surrounding boards. After finding a matching stain color by experimenting on scraps of flooring, stain the boards to match the original floor. Let dry overnight, then apply two coats of clear polyurethane varnish. If the old floor is unstained, just apply the polyurethane. Denver Hardwood Flooring

One of the best things about cork floors is that they are environmentally friendly because cork is a sustainable and renewable resource. The natural beauty of the material can suite any decor. The structure of the cork allows for a natural comfort and softness to absorb shock. This is why use of cork flooring is a good application in areas where people will be on their feet for extended periods of time. Using cork floors will reduce noise from traffic or dropping items, also because of the structure of the cork material. The natural properties of the material make it healthy because it is not only resistant to insects, but it is hypo-allergenic.
It’s important to start by knowing what kind of finish is on your floor. Is your finish oil or water based? Do you have a wax coating? Is the wood varnished or stained? Is there an aluminum oxide coating? Know what the surface is made of so you know how to start your wood floor scratch repair. If you didn’t install the floor and aren’t sure what type of finish it has, you can check here for more details on identifying it.
Wood flooring is any product manufactured from timber that is designed for use as flooring, either structural or aesthetic. Wood is a common choice as a flooring material and can come in various styles, colors, cuts, and species. Bamboo flooring is often considered a form of wood flooring, although it is made from a grass (bamboo) rather than a timber.[1] Denver Hardwood Flooring
Regardless of the floor, the protective finish will play a large role in how scratch and stain resistant it is. Both hardwood and Rigid Core flooring are available with various types of protective finishes. Rigid Core flooring goes a step beyond hardwood though, and also has a transparent solid wear layer that protects against gouging and deeper scratches. Denver Hardwood Floors
You cannot restore every wood floor by simply refinishing it. If your wood floor has become warped or if several of the planks have become damaged, you will typically need to replace the entire floor, as finishing will only brighten an already-damaged surface. On really old floors, you may see the tongue where the boards come together, or your boards may lack adequate thickness. Floors like this are definite candidates for replacement, as refinishing is purely cosmetic. Denver Hardwood Floor Install

Visual – While hardwood flooring is limited by species and stains, Rigid Core flooring has near limitless options when it comes to flooring that looks like wood. In addition to traditional wood visuals and colors, you can pick from stone looks and even hybrids that marry wood and stones together into unique new options. And best of all you will benefit from a curated look that removes unwanted imperfections like oversized knots, holes, and worming that naturally occurs in hardwood floors.
If your floor has noticeable scratches throughout, your best option is to sand down the floor and refinish it. A complete sanding removes scratches, but beware: This only works on real wood floors, not bamboo. If you have an engineered wood floor with a real wood surface, make sure the real wood surface is more than 1mm thick—sanding usually takes at least this much wood off the surface, so a thicker layer is required for a complete sanding. Hardwood Floors
This process involves treating the wood by boiling the log in water. After preparation, the wood is peeled by a blade starting from the outside of the log and working toward the center, thus creating a wood veneer. The veneer is then pressed flat with high pressure. This style of manufacturing tends to have problems with the wood cupping or curling back to its original shape. Rotary-peeled engineered hardwoods tend to have a plywood appearance in the grain.[3] Hardwood Floors
×